Supero SUPER P6DBE Скачать руководство пользователя страница 79

Страница: 79 / 104

Chapter 5: Running Setup

5-13

Type F DMA Buffer Control1

Type F DMA Buffer Control2

These options specify the DMA channel where Type F buffer control is

implemented. The settings are

Disabled

Channel-0

Channel-1

Chan-

nel-2

Channel-3

Channel-4

Channel-5

Channel-6

Channel-7

DMA0 Type

DMA1 Type

DMA2 Type

DMA3 Type

DMA5 Type

DMA6 Type

DMA7 Type

These options specify the bus that the specified DMA channel can be

used on. The settings are

PC/PCI

Distributed

, or

Normal ISA

Memory Buffer Strength

The settings for this option are

Strong

Auto

Manufacturer's Setting

Note: The user should always set this option to mode 0. All other

modes are for factory testing only

5-1-4 Power Management

Power Management

The settings for this feature are:

APM

ACPI

Disabled

. Set to

APM

enable the power conservation feature specified by Intel and Microsoft

INT 15h Advance Power Management BIOS functions. Set to

ACPI

if your

operating system supports Microsoft's Advanced Configuration and Power

Interface (ACPI) standard.

Power Button Function

This option specifies how the power button mounted externally on the

computer chassis is used. The settings are:

Suspend

On/Off

. When

set to

On/Off

, pushing the power button turns the computer on or off.

When set to

Suspend

, pushing the power button places the computer in

Suspend mode or Full On power mode.

Green PC Monitor Power State

This option specifies the power state that the green PC-compliant video

monitor enters when AMIBIOS places it in a power savings state after the

Содержание SUPER P6DBE









































































































Результаты поиска

Содержание SUPER P6DBE

Отзывы:

Похожие инструкции для SUPER P6DBE

Бренды по названию

Популярные бренды

Supero SUPER P6DBE, Руководство пользователя

Результаты поиска

Содержание SUPER P6DBE

Отзывы:

Похожие инструкции для SUPER P6DBE

Бренды по названию

Популярные бренды