Supero SUPER P6DBE Скачать руководство пользователя страница 80

Страница: 80 / 104

BIOS User's Manual

5-14

specified period of display inactivity has expired. The settings are

Standby

Suspend

Off

Note: The Optimal default setting for this

option is Suspend and the Fail-Safe setting is Standby

Video Power Down Mode

This option specifies the power conserving state that the VGA video

subsystem enters after the specified period of display inactivity has

expired. The settings are

Disabled

Standby

, or

Suspend

Note: The

Optimal default setting for this option is Suspend and the Fail-

Safe default setting is Disabled

Hard Disk Power Down Mode

This option specifies the power conserving state that the hard disk drive

enters after the specified period of hard drive inactivity has expired. The

settings are

Disabled

Standby

, or

Suspend

Note: The Optimal

default setting for this option is Suspend and the Fail-Safe

default setting is Disabled

Hard Disk Timeout (Minutes)

This option specifies the length of a period of hard disk drive inactivity.

When this length of time expires, the computer enters power-conserving

state specified in the Hard Disk Power Down Mode option. The settings

are

Disabled

and

1 Min through 15 Min in 1 minute intervals

Power Saving Type

The settings for this option are

Sleep, Stop Clock or Deep Sleep

Standby/Suspend Timer Unit

This allows you to set the standby timeout and suspend timeout timer unit.

The settings are

32 secs

4 msecs

4 min

4 secs

Standby Timeout

This option specifies the length of a period of system inactivity while in

full power on state. When this length of time expires, the computer

enters standby power state. The settings are

Disabled

and

4 Min

through 508 Min in 4 minute intervals

Suspend Timeout (Minutes)

This option specifies the length of a period of system inactivity while in

standby state. When this length of time expires, the computer enters

suspend power state. The settings are

Disabled

and

4 Min through 508

Min in 4 minute intervals

Содержание SUPER P6DBE









































































































Результаты поиска

Содержание SUPER P6DBE

Отзывы:

Похожие инструкции для SUPER P6DBE

Бренды по названию

Популярные бренды

Supero SUPER P6DBE, Руководство пользователя

Результаты поиска

Содержание SUPER P6DBE

Отзывы:

Похожие инструкции для SUPER P6DBE

Бренды по названию

Популярные бренды