Supero AS2021M-UR Plus Скачать руководство пользователя

Страница: 14 / 104

1-4

AS2021M-UR+ User's Manual

Front Control Panel

The control panel on the SuperServer 2021M-UR+ provides you with system

monitoring and control. LEDs indicate system power, HDD activity, network activ-

ity, system overheat and power supply failure. A main power button and a system

reset button are also included. In addition, two USB ports have been incorporated

into the control panel to provide front side USB access.

I/O Backplane

The SC825TQ-R700U is an ATX form factor chassis designed to be used in a

2U rackmount conﬁ guration. The I/O backplane provides seven low-proﬁ le PCI

expansion slots, one COM port, a VGA port, two USB 2.0 ports, PS/2 mouse and

keyboard ports and two gigabit Ethernet ports.

Cooling System

The SC825TQ-R700U chassis has an innovative cooling design that includes three

8-cm hot-plug system cooling fans located in the middle section of the chassis. An

air shroud channels the airﬂ ow from the system fans to efﬁ ciently cool the processor

area of the system. The power supply module also includes a cooling fan.

Содержание AS2021M-UR Plus









































































































Результаты поиска

Содержание AS2021M-UR Plus

Отзывы:

Похожие инструкции для AS2021M-UR Plus

Бренды по названию

Популярные бренды

Supero AS2021M-UR Plus, Руководство пользователя

Результаты поиска

Содержание AS2021M-UR Plus

Отзывы:

Похожие инструкции для AS2021M-UR Plus

Бренды по названию

Популярные бренды