Supero AS2021M-UR Plus Скачать руководство пользователя

Страница: 36 / 104

5-2

AS2021M-UR+ User's Manual

5-2 Processor and Heatsink Installation

Installing the Processor (install to the CPU#1 socket ﬁ rst)

1. Begin by removing the cover plate

that protects the CPU. Lift the lever

on CPU socket #1 until it points straight

up. With the lever raised, lift open the

silver CPU retention plate.

2. Use your thumb and your index

ﬁ nger to hold the CPU. Locate and

align pin 1 of the CPU socket with pin

1 of the CPU. Both are marked with

a triangle.

Triangles

CPU Backplates

Two CPU backplates (BKT-0011L) have been preinstalled to the serverboard to

prevent the CPU area of the serverboard from bending and to provide a base for

attaching the heatsink retention modules.

Exercise extreme caution when handling and installing the proces-

sor. Always connect the power cord last and always remove it be-

fore adding, removing or changing any hardware components.

Содержание AS2021M-UR Plus









































































































Результаты поиска

Содержание AS2021M-UR Plus

Отзывы:

Похожие инструкции для AS2021M-UR Plus

Бренды по названию

Популярные бренды

Supero AS2021M-UR Plus, Руководство пользователя

Результаты поиска

Содержание AS2021M-UR Plus

Отзывы:

Похожие инструкции для AS2021M-UR Plus

Бренды по названию

Популярные бренды