Supero AS2021M-UR Plus Скачать руководство пользователя страница 47

Страница: 47 / 104

Chapter 5: Advanced Serverboard Setup

5-13

NIC1 LED

The NIC1 (Network Interface Control-

ler) LED connection is located on pins

11 and 12 of JF1. Attach the NIC1

LED cable to display network activity.

Refer to the table on the right for pin

deﬁ nitions.

NIC2 LED

The NIC2 (Network Interface Control-

ler) LED connection is located on pins

9 and 10 of JF1. Attach the NIC2

LED cable to display network activity.

Refer to the table on the right for pin

deﬁ nitions.

NIC1 LED

Pin Deﬁ nitions (JF1)

Pin# Deﬁ nition

Vcc

NIC1 Active

NIC2 LED

Pin Deﬁ nitions (JF1)

Pin# Deﬁ nition

Vcc

NIC2 Active

HDD LED

The HDD (IDE Hard Disk Drive) LED

connection is located on pins 13 and

14 of JF1. Attach the IDE hard drive

LED cable to display disk activity.

Refer to the table on the right for pin

deﬁ nitions.

HDD LED

Pin Deﬁ nitions (JF1)

Pin# Deﬁ nition

See below*

HDD Active

* Pin 13 is for UID button (when used with UID

panel) or for 3.3V power for HDD LED (when

used with non-UID panel)

Universal Information LED

Connect an LED to pins 7 and 8 of

JF1 to provide advanced warning of

chassis overheating or fan failure.

These pins also work with the front

UID indicator, which will activate as

either a solid or ﬂ ashing blue LED

depending on whether the LED was

activated via IPMI or the UID button.

Refer to the tables on the right for pin

deﬁ nitions and status indicators.

Universal Info. LED

Pin Deﬁ nitions (JF1)

Pin# Deﬁ nition

Vcc

Control

Red LED Indications

State Indication

Solid

Overheat

Blinking (fast)

Fan Fail

Blinking (slow)

Power Fail

Blue LED Indications

State Indication

Solid

UID (via Button)

Blinking

UID (via IPMI)

Содержание AS2021M-UR Plus









































































































Результаты поиска

Содержание AS2021M-UR Plus

Отзывы:

Бренды по названию

Популярные бренды

Supero AS2021M-UR Plus, Руководство пользователя

Результаты поиска

Содержание AS2021M-UR Plus

Отзывы:

Бренды по названию

Популярные бренды