Supero AS2021M-UR Plus Скачать руководство пользователя

Страница: 49 / 104

Chapter 5: Advanced Serverboard Setup

5-15

Fan Headers

The H8DMU+ has eight fan headers,

which are designated FAN1 through

FAN8. FAN7 and FAN8 (for active

CPU heatsinks) are Pulse Width

Modulated (PWM): their speed is

controlled via a BIOS setting. See the

table on the right for pin deﬁ nitions.

Note:

when using active heatsinks

(those with fans), connect the heatsink

fan for CPU1 to the FAN7 header and

the heatsink fan for CPU2 to the FAN8

header.

Serial Ports

The COM1 serial port is located be-

side the VGA port. COM2 is a header

located near JWOL. Refer to the table

on the right for pin deﬁ nitions.

LAN1/2 (Ethernet Ports)

Two Gigabit Ethernet ports (desig-

nated LAN1 and LAN2) are located

beside the VGA port. These Ethernet

ports accept RJ45 type cables.

Note:

NC indicates no connection.

Serial Port Pin Deﬁ nitions

(COM1/COM2)

Pin # Deﬁ nition

DCD

DSR

RXD

RTS

TXD

CTS

DTR

Ground

Fan Header

Pin Deﬁ nitions

(FAN1-8)

Pin# Deﬁ nition

Ground (Black)

+12V (Red)

Tachometer

PWM Control

USB Headers

Four additional USB2.0 headers

(USB4/5 and USB6/7) are included on

the serverboard. These may be con-

nected to provide front side access.

A USB cable (not included) is needed

for the connection. See the table on

the right for pin deﬁ nitions.

Universal Serial Bus Headers

Pin Deﬁ nitions (USB4/5/6/7)

USB2
Pin # Deﬁ nition

USB3/4
Pin # Deﬁ nition

+5V

PO-

PO+

Ground

Key

No connection

Содержание AS2021M-UR Plus









































































































Результаты поиска

Содержание AS2021M-UR Plus

Отзывы:

Похожие инструкции для AS2021M-UR Plus

Бренды по названию

Популярные бренды

Supero AS2021M-UR Plus, Руководство пользователя

Результаты поиска

Содержание AS2021M-UR Plus

Отзывы:

Похожие инструкции для AS2021M-UR Plus

Бренды по названию

Популярные бренды