Supero AS2021M-UR Plus Скачать руководство пользователя

Страница: 13 / 104

1-3

Chapter 1: Introduction

ATI Graphics Controller

The H8DMU+ features an integrated ATI video controller based on the ES1000

graphics chip. The ES1000 was designed speciﬁ cally for servers, featuring low

power consumption, high reliability and superior longevity.

Other Features

Other onboard features that promote system health include onboard voltage moni-

tors, a chassis intrusion header, auto-switching voltage regulators, chassis and CPU

overheat sensors, virus protection and BIOS rescue.

1-3 Server

Chassis

Features

The following is a general outline of the main features of the SC825TQ-R700U

server chassis.

System Power

The SC825TQ-R700U features a redundant 700W power supply composed of two

separate power modules. This power redundancy feature allows you to replace a

failed power supply without shutting down the system.

Serial ATA Subsystem

The SC825TQ-R700U supports up to eight 3 Gb/s Serial ATA drives. The Serial

ATA drives are hot-swappable units and are connected to a backplane that provides

power and control.

Note:

The operating system you use must have RAID support to enable the hot-

swap capability of the Serial ATA drives.

PCI Expansion Slots

When conﬁ gured as a 2021M-UR+ server, the SC825TQ-R700U suppports expan-

sion cards on both the left and right sides of the chassis:

Left side: UIO card and three PCI-Express x8 cards (with RSC-R2UU-UA3E8 riser

card.)

Right side: one PCI-E x8 card and one PCI-E x4 card in a x8 slot (with RSC-R2UU-

2E8R riser card). (Left and right refer to the side when viewed from the front of the

chassis.)

Содержание AS2021M-UR Plus









































































































Результаты поиска

Содержание AS2021M-UR Plus

Отзывы:

Похожие инструкции для AS2021M-UR Plus

Бренды по названию

Популярные бренды

Supero AS2021M-UR Plus, Руководство пользователя

Результаты поиска

Содержание AS2021M-UR Plus

Отзывы:

Похожие инструкции для AS2021M-UR Plus

Бренды по названию

Популярные бренды