Supero AS2021M-UR Plus Скачать руководство пользователя

Страница: 50 / 104

5-16

AS2021M-UR+ User's Manual

ATX PS/2 Keyboard and
PS/2 Mouse Ports

The ATX PS/2 keyboard and the PS/2

mouse ports are located on the I/O

backplane. The mouse is the top

(green) port. See the table on the

right for pin deﬁ nitions.

PS/2 Keyboard and

Mouse Port Pin

Deﬁ nitions

Pin# Deﬁ nition

Data

Ground

VCC

Clock

Overheat LED

Connect an LED to the JOH1 header

to provide warning of chassis over-

heating. See the table on the right for

pin deﬁ nitions.

Overheat LED

Pin Deﬁ nitions (JOH1)

Pin# Deﬁ nition

3.3V

OH Active

Power LED/Speaker

On JD1, pins 1, 2, and 3 are for the

power LED and pins 4 through 7 are

for the speaker. See the tables on the

right for pin deﬁ nitions.

Note:

The speaker connector pins are

for use with an external speaker. If

you wish to use the onboard speaker,

you should close pins 6 and 7 with a

jumper.

Speaker Connector

Pin Deﬁ nitions (JD1)

Pin# Deﬁ nition

Red wire, +5V

No connection

Buzzer signal

Speaker data

PWR LED Connector

Pin Deﬁ nitions (JD1)

Pin# Deﬁ nition

+Vcc

Control

Chassis Intrusion

A Chassis Intrusion header is located

at JL1. Attach the appropriate cable

to inform you of a chassis intrusion.

Chassis Intrusion

Pin Deﬁ nitions (JL1)

Pin# Deﬁ nition

Battery voltage

Intrusion signal

Содержание AS2021M-UR Plus









































































































Результаты поиска

Содержание AS2021M-UR Plus

Отзывы:

Похожие инструкции для AS2021M-UR Plus

Бренды по названию

Популярные бренды

Supero AS2021M-UR Plus, Руководство пользователя

Результаты поиска

Содержание AS2021M-UR Plus

Отзывы:

Похожие инструкции для AS2021M-UR Plus

Бренды по названию

Популярные бренды