Supero AS2021M-UR Plus Скачать руководство пользователя

Страница: 69 / 104

Chapter 6: Advanced Chassis Setup

6-7

Hard Drive Backplane

The SATA drives plug into a backplane that provides power, drive ID and bus termi-

nation. A RAID controller can be used with the backplane to provide data security.

The operating system you use must have RAID support to enable the hot-swap

capability of the drives. The backplane is already preconﬁ gured, so there are no

jumpers or switches present on it.

DVD-ROM and Floppy Drive Installation

The top cover of the chassis must be opened to gain full access to the DVD-ROM

and ﬂ oppy drive bays. The 2021M-UR+ accomodates only slim type DVD-ROM

drives. Side mounting brakets are typically needed to mount a slim DVD-ROM

drive in the 2021M-UR+ server.

First, grasp the two handles on either side and pull the unit straight out until it locks

(you will hear a "click"). Next, depress the two buttons on the top of the chassis

to release the top cover and at the same time, push the cover away from you until

it stops. You can then lift the top cover from the chassis to gain full access to the

inside of the server. You must power down the system before installing or removing

ﬂ oppy or IDE components.

Drives mount on rails and should "click" into place to be correctly and fully installed

in their bays.

• The ﬂ oppy disk drive cable has seven twisted wires.

• A color mark on a cable typically designates the location of pin 1.

• A single ﬂ oppy disk drive ribbon cable has 34 wires and two connectors to provide

for two ﬂ oppy disk drives. The connector with twisted wires always connects to

drive A, and the connector without twisted wires always connects to drive B.

Содержание AS2021M-UR Plus









































































































Результаты поиска

Содержание AS2021M-UR Plus

Отзывы:

Похожие инструкции для AS2021M-UR Plus

Бренды по названию

Популярные бренды

Supero AS2021M-UR Plus, Руководство пользователя

Результаты поиска

Содержание AS2021M-UR Plus

Отзывы:

Похожие инструкции для AS2021M-UR Plus

Бренды по названию

Популярные бренды