Supero AS2021M-UR Plus Скачать руководство пользователя страница 39

Страница: 39 / 104

Chapter 5: Advanced Serverboard Setup

5-5

5-3 Connecting

Cables

Now that the processors are installed, the next step is to connect the cables to

the serverboard. These include the data (ribbon) cables for the peripherals and

control panel and the power cables.

Connecting Data Cables

The cables used to transfer data from the peripheral devices have been carefully

routed in preconﬁ gured systems to prevent them from blocking the ﬂ ow of cooling

air that moves through the system from front to back. If you need to disconnect

any of these cables, you should take care to reroute them as they were originally

after reconnecting them (make sure the red wires connect to the pin 1 locations).

If you are conﬁ guring the system, keep the airﬂ ow in mind when routing the

cables. The following data cables (with their serverboard connector locations

noted) should be connected. See the serverboard layout diagram in this chapter

for connector locations.

DVD-ROM Drive cable (IDE#1)

Control Panel cable (JF1, see next page)

SAS or SATA cables (up to 8)

Connecting Power Cables

The H8DMU+ has a 20-pin primary power supply connector designated "JPW1"

for connection to the ATX power supply. Connect the appropriate connector from

the power supply to JPW1 to supply power to the serverboard. See the Connector

Deﬁ nitions section in this chapter for power connector pin deﬁ nitions.

In addition, your power supply must be connected to the 4-pin Auxiliary ATX Power

connection at J32 and the 8-pin Processor Power connector at JPW2.

Содержание AS2021M-UR Plus









































































































Результаты поиска

Содержание AS2021M-UR Plus

Отзывы:

Бренды по названию

Популярные бренды

Supero AS2021M-UR Plus, Руководство пользователя

Результаты поиска

Содержание AS2021M-UR Plus

Отзывы:

Бренды по названию

Популярные бренды