Supero AS-1011M-Ni Скачать руководство пользователя страница 14

Страница: 14 / 100

1-4

AS1011M-Ni User's Manual

1-3 Server Chassis Features

The SC812L-280U is Supermicro's second-generation 1U chassis and features

three hard drive bays and a revolutionary cooling design that can keep today's most

powerful processors running well below their temperature thresholds. The following

is a general outline of the main features of the SC812L-280U chassis.

System Power

The SC812L-280U chassis features a 280W power supply.

Control Panel

The SC812L-280U control panel provides important system monitoring and control

information. LEDs indicate power on, network activity, hard disk drive activity, UID

and system overheat conditions. Also present are a main power button, a system

reset button and a UID button.

I/O Backplane

The SC812L-280U is a 1U rackmount chassis. Its I/O backplane provides three

standard size PCI slots, one COM port (the other is internal), one VGA port, two USB

ports, PS/2 mouse and keyboard ports, two Ethernet (LAN) ports and a UID LED.

Cooling System

The SC812L-280U chassis has a revolutionary cooling design. The SC812L-280U

includes two heavy duty 10-cm blower fans located in the middle of the chassis.

These fans operate continuously at full rpm. An overheat LED will be activated if

they break down and the ambient air temperature inside the chassis rises.

Содержание AS-1011M-Ni





































































































Результаты поиска

Содержание AS-1011M-Ni

Отзывы:

Похожие инструкции для AS-1011M-Ni

Бренды по названию

Популярные бренды

Supero AS-1011M-Ni, Руководство пользователя

Результаты поиска

Содержание AS-1011M-Ni

Отзывы:

Похожие инструкции для AS-1011M-Ni

Бренды по названию

Популярные бренды