Supero AS-1011M-Ni Скачать руководство пользователя страница 82

Страница: 82 / 100

7-14

AS1011M-Ni User's Manual

Event Log Confi guration

View Event Log

Highlight this item and press <Enter> to view the contents of the event log.

Mark All Events as Read

Highlight this item and press <Enter> to mark all events as read.

Clear Event Log

Select Yes and press <Enter> to clear all event logs. The options are Yes and

No to verify.

PCI Express Confi guration

Use this setting to Enable or

Disable

the Active State Power Management

feature.

Remote Access Confi guration

Remote Access

Allows you to Enable or

Disable

remote access. If enabled, the settings below

will appear.

Serial Port Number

Selects the serial port to use for console redirection. Options are

COM1

and

COM2.

Serial Port Mode

Selects the serial port settings to use. Options are

(115200 8, n, 1)

, (57600 8,

n, 1), (38400 8, n, 1), (19200 8, n, 1) and (09600 8, n, 1).

Flow Control

Selects the fl ow control to be used for console redirection. Options are

None,

Hardware and Software.

MAC1 LAN1 Bridge

Settings are

Enabled

and Disabled for MAC1 LAN1 bridge.

MCP55 PCI-E Confi guration

Settings are x16 x0 x4 x0 x0 x8, x4 x4 x4 x4 x4 x8, and

x8 x8 x4 x0 x0 x8

Содержание AS-1011M-Ni





































































































Результаты поиска

Содержание AS-1011M-Ni

Отзывы:

Похожие инструкции для AS-1011M-Ni

Бренды по названию

Популярные бренды

Supero AS-1011M-Ni, Руководство пользователя

Результаты поиска

Содержание AS-1011M-Ni

Отзывы:

Похожие инструкции для AS-1011M-Ni

Бренды по названию

Популярные бренды