Supero AS-1011M-Ni Скачать руководство пользователя страница 84

Страница: 84 / 100

7-16

AS1011M-Ni User's Manual

7-4 Boot

Menu

This feature allows the user to confi gure the following items:

Boot Device Priority

This feature allows the user to prioritize the boot sequence from the available de-

vices. The devices to set are:

· 1st Boot Device

· 2nd Boot Device

· 3rd Boot Device

· 4th Boot Device

Hard Disk Drives

This feature allows the user to specify the boot sequence from the available hard

disk

drives.

Removable Drives

This feature allows the user to specify the Boot sequence from the available re-

movable drives.

7-5 Security

Menu

AMI BIOS provides a Supervisor and a User password. If you use both passwords,

the Supervisor password must be set fi rst.

Change Supervisor Password

Select this option and press <Enter> to access the sub menu, and then type in

the password.

Change User Password

Select this option and press <Enter> to access the sub menu, and then type in

the password.

Содержание AS-1011M-Ni





































































































Результаты поиска

Содержание AS-1011M-Ni

Отзывы:

Похожие инструкции для AS-1011M-Ni

Бренды по названию

Популярные бренды

Supero AS-1011M-Ni, Руководство пользователя

Результаты поиска

Содержание AS-1011M-Ni

Отзывы:

Похожие инструкции для AS-1011M-Ni

Бренды по названию

Популярные бренды