Supero AS-1011M-Ni Скачать руководство пользователя страница 28

Страница: 28 / 100

3-2

AS1011M-Ni User's Manual

3-3

Control Panel LEDs

The control panel located on the front of the SC812L-280U chassis has fi ve LEDs.

These LEDs provide you with critical information related to different parts of the

system. This section explains what each LED indicates when illuminated and any

corrective action you may need to take.

Universal Information LED:

When this LED blinks red slowly, it indicates

a fan failure and when blinking red quickly a power failure. This LED will be blue

when used for UID (Unit Identifi er). When on continuously it indicates an overheat

condition, which may be caused by cables obstructing the airfl ow in the system or

the ambient room temperature being too warm. Check the routing of the cables

and make sure all fans are present and operating normally. You should also check

to make sure that the chassis covers are installed. Finally, verify that the heatsinks

are installed properly (see Chapter 5). This LED will remain fl ashing or on as long

as the indicated condition exists. See the table below for descriptions of the LED

states.

Figure 3-1. Universal Information LED States

Universal Information LED States

State Indication

Fast Blinking Red (4x/sec)

Fan Fail

Solid Red

CPU Overheat

Slow Blinking Red (1x/sec)

Power Fail

Solid Blue

Local UID Button Depressed

Blinking Blue

IPMI-Activated UID

Note:

deactivating the UID LED must be performed in the same way it was acti-

vated. (If the UID LED was activated via IPMI, you can only turn the LED off via

IPMI and not with the UID button.)

Содержание AS-1011M-Ni





































































































Результаты поиска

Содержание AS-1011M-Ni

Отзывы:

Похожие инструкции для AS-1011M-Ni

Бренды по названию

Популярные бренды

Supero AS-1011M-Ni, Руководство пользователя

Результаты поиска

Содержание AS-1011M-Ni

Отзывы:

Похожие инструкции для AS-1011M-Ni

Бренды по названию

Популярные бренды