Supero AS-1011M-Ni Скачать руководство пользователя страница 47

Страница: 47 / 100

Chapter 5: Advanced Motherboard Setup

5-13

NIC1 LED

The NIC1 (Network Interface Control-

ler) LED connection is located on pins

11 and 12 of JF1. Attach the NIC1

LED cable to display network activity

on LAN1. Refer to the table on the

right for pin defi nitions.

NIC2 LED

The NIC2 (Network Interface Control-

ler) LED connection is located on pins

9 and 10 of JF1. Attach the NIC2 LED

cable to display network activity on

LAN2. Refer to the table on the right

for pin defi nitions.

NIC1 LED

Pin Defi nitions (JF1)

Pin# Defi nition

Vcc

NIC1 Active

NIC2 LED

Pin Defi nitions (JF1)

Pin# Defi nition

Vcc

NIC2 Active

Universal Information LED

Connect an LED to pins 7 and 8 of

JF1 to provide advanced warning of

chassis overheating, a fan failure or

a power supply failure. These pins

also work with the front UID indicator,

which will activate as either a solid

or fl ashing blue LED depending on

whether the LED was activated via

IPMI or the UID button. Refer to the

tables on the right for pin defi nitions

and status indicators.

OH/Fan Fail/Power Fail LED

Pin Defi nitions (JF1)

Pin# Defi nition

UID LED Signal

OH/Fan Fail/Pwr Fail Signal

Red LED Indications

State Indication

Solid

Overheat

Blinking (1/4 Hz)

Power Fail

Blinking (1 Hz)

Fan Fail

Blue LED Indications

State Indication

Solid

UID (via Button)

Blinking

UID (via IPMI)

Содержание AS-1011M-Ni





































































































Результаты поиска

Содержание AS-1011M-Ni

Отзывы:

Похожие инструкции для AS-1011M-Ni

Бренды по названию

Популярные бренды

Supero AS-1011M-Ni, Руководство пользователя

Результаты поиска

Содержание AS-1011M-Ni

Отзывы:

Похожие инструкции для AS-1011M-Ni

Бренды по названию

Популярные бренды