Supero AS-1011M-Ni Скачать руководство пользователя страница 17

Страница: 17 / 100

Chapter 2: Server Installation

2-1

Chapter 2

Server Installation

2-1 Overview

This chapter provides a quick setup checklist to get your 1011M-Ni system up and

running. Following these steps in the order given should enable you to have the

system operational within a minimum amount of time. This quick setup assumes

that your 1011M-Ni system has come to you with the processors and memory

preinstalled. If your system is not already fully integrated with a motherboard, pro-

cessors, system memory etc., please turn to the chapter or section noted in each

step for details on installing specifi c components.

2-2 Unpacking the System

You should inspect the box the 1011M-Ni was shipped in and note if it was damaged

in any way. If the server itself shows damage you should fi le a damage claim with

the carrier who delivered it.

Decide on a suitable location for the rack unit that will hold the 1011M-Ni. It should

be situated in a clean, dust-free area that is well ventilated. Avoid areas where

heat, electrical noise and electromagnetic fi elds are generated. You will also need

it placed near a grounded power outlet. Read the Rack and Server Precautions in

the

section.

2-3 Preparing for Setup

The box the 1011M-Ni was shipped in should include two sets of rail assemblies, two

rail mounting brackets and the mounting screws you will need to install the system

into the rack. Follow the steps in the order given to complete the installation process

in a minimum amount of time. Please read this section in its entirety before you

begin the installation procedure outlined in the sections that follow.

Содержание AS-1011M-Ni





































































































Результаты поиска

Содержание AS-1011M-Ni

Отзывы:

Похожие инструкции для AS-1011M-Ni

Бренды по названию

Популярные бренды

Supero AS-1011M-Ni, Руководство пользователя

Результаты поиска

Содержание AS-1011M-Ni

Отзывы:

Похожие инструкции для AS-1011M-Ni

Бренды по названию

Популярные бренды