Supero AS-1011M-Ni Скачать руководство пользователя страница 83

Страница: 83 / 100

Chapter 7: BIOS

7-15

Redirection After BIOS POST

Options are Disable (no redirection after BIOS POST), Boot Loader (redirection

during POST and during boot loader) and

Always

(redirection always active).

Note that some OS's may not work with this set to Always.

Terminal Type

Selects the type of the target terminal. Options are

ANSI

, VT100 and VT-

UTF8.

VT-UTF8 Combo Key Support

Allows you to

Enable

or Disable VT-UTF8 combination key support for ANSI/

VT100 terminals.

Sredir Memory Display Delay

Use this setting to set the delay in seconds to display memory information. Op-

tions are

No Delay

, 1 sec, 2 secs and 4 secs.

System Health Monitor

CPU Overheat Temperature

Use the "+" and "-" keys to set the CPU temperature threshold to between 65

and 90

C. When this threshold is exceeded, the overheat LED on the chas-

sis will light up and an alarm will sound. The LED and alarm will turn off once

the CPU temperature has dropped to 5 degrees below the threshold set. The

default setting is

Fan Speed Control Modes

This feature allows the user to determine how the system will control the speed

of the onboard fans. Select "Workstation" if your system is used as a Worksta-

tion. Select "Server" if your system is used as a Server. Select "Disable" to

disable the fan speed control function to allow the onboard fans to continuously

run at full speed (12V). The options are

1) Disable (Full Speed),

2) Server

Mode 3) Workstation Mode.

Below this setting the current fan speeds are displayed.

System monitor displays are also given for the following information:

CPU Temperature, System Temperature, CPU1 VCore, 3.3V Vcc (V), +5Vin,

+12Vin, 5V Standby and Battery Voltage.

Содержание AS-1011M-Ni





































































































Результаты поиска

Содержание AS-1011M-Ni

Отзывы:

Похожие инструкции для AS-1011M-Ni

Бренды по названию

Популярные бренды

Supero AS-1011M-Ni, Руководство пользователя

Результаты поиска

Содержание AS-1011M-Ni

Отзывы:

Похожие инструкции для AS-1011M-Ni

Бренды по названию

Популярные бренды