Supero AS-1011M-Ni Скачать руководство пользователя страница 18

Страница: 18 / 100

2-2

AS1011M-Ni User's Manual

Choosing a Setup Location

- Leave enough clearance in front of the rack to enable you to open the front door

completely (~25 inches).

- Leave approximately 30 inches of clearance in the back of the rack to allow for

suffi cient airfl ow and ease in servicing.

- This product is for installation only in a Restricted Access Location (dedicated

equipment rooms, service closets and the like).

- This product is not suitable for use with visual display work place devices according

to §2 of the the German Ordinance for Work with Visual Display Units.

Rack Precautions:

- Ensure that the leveling jacks on the bottom of the rack are fully extended to

the fl oor with the full weight of the rack resting on them.

- In single rack installation, stabilizers should be attached to the rack.

- In multiple rack installations, the racks should be coupled together.

- Always make sure the rack is stable before extending a component from the

rack.

- You should extend only one component at a time - extending two or more

simultaneously may cause the rack to become unstable.

Server Precautions:

- Review the electrical and general safety precautions in Chapter 4.

- Determine the placement of each component in the rack

before

you install the

rails.

Install the heaviest server components on the bottom of the rack fi rst, and then

work up.

- Use a regulating uninterruptible power supply (UPS) to protect the server from

power surges, voltage spikes and to keep your system operating in case of a

power failure.

Allow the power supply units to cool before touching them.

Always keep the rack's front door and all panels and components on the serv-

ers closed when not servicing to maintain proper cooling.

Warnings and Precautions!

Содержание AS-1011M-Ni





































































































Результаты поиска

Содержание AS-1011M-Ni

Отзывы:

Похожие инструкции для AS-1011M-Ni

Бренды по названию

Популярные бренды

Supero AS-1011M-Ni, Руководство пользователя

Результаты поиска

Содержание AS-1011M-Ni

Отзывы:

Похожие инструкции для AS-1011M-Ni

Бренды по названию

Популярные бренды