Supero AS-1011M-Ni Скачать руководство пользователя страница 8

Страница: 8 / 100

viii

ATX PS/2 Keyboard & Mouse Ports ...................................................... 5-16

Power Supply I

C Header ...................................................................... 5-16

Wake-On-LAN ........................................................................................ 5-17

Wake-On-Ring ........................................................................................ 5-17

Chassis Intrusion .................................................................................... 5-17

Compact Flash Power Header ............................................................... 5-18

SGPIO .................................................................................................... 5-18

5-10 Jumper Settings ............................................................................................ 5-19

Explanation of Jumpers ......................................................................... 5-19

CMOS Clear ........................................................................................... 5-19

VGA Enable/Disable ............................................................................... 5-20

Watch Dog Enable/Disable .................................................................... 5-20

Onboard Speaker Enable/Disable .......................................................... 5-20

Compact Flash Master/Slave ................................................................. 5-21

C to PCI-X/PCI-E Enable/Disable ........................................................ 5-21

5-11 Onboard Indicators ....................................................................................... 5-22

LAN1/LAN2 LEDs .................................................................................. 5-22

Onboard Power LED (DP1) ................................................................... 5-22

UID LED (LE1) ....................................................................................... 5-22

5-12 Floppy, IDE and SATA Drive Connections ................................................... 5-23

Floppy Connector ................................................................................... 5-23

IDE Connector ........................................................................................ 5-24

SATA Ports ............................................................................................. 5-24

5-13 Enabling SATA RAID .................................................................................... 5-25

5-14 Installing Drivers ........................................................................................... 5-28

Chapter 6: Advanced Chassis Setup

6-1 Static-Sensitive Devices ................................................................................. 6-1

6-2 Control Panel .................................................................................................. 6-2

6-3 System Fans ................................................................................................... 6-3

System Fan Failure .................................................................................. 6-3

Replacing System Cooling Fans .............................................................. 6-3

6-4 Drive Bay Installation/Removal ....................................................................... 6-4

Accessing the Drive Bays ........................................................................ 6-4

Installing Components in the 3.5" Drive Bays ......................................... 6-5

6-5 Power Supply ................................................................................................. 6-6

Power Supply Failure ............................................................................... 6-6

Removing/Replacing the Power Supply ................................................... 6-6

AS1011M-Ni User's Manual

Содержание AS-1011M-Ni





































































































Результаты поиска

Содержание AS-1011M-Ni

Отзывы:

Похожие инструкции для AS-1011M-Ni

Бренды по названию

Популярные бренды

Supero AS-1011M-Ni, Руководство пользователя

Результаты поиска

Содержание AS-1011M-Ni

Отзывы:

Похожие инструкции для AS-1011M-Ni

Бренды по названию

Популярные бренды