Supermicro AS-1020P-8R Скачать руководство пользователя страница 81

Страница: 81 / 104

Chapter 7: BIOS

7-9

Remote Access Conﬁ guration

Remote Access

Use this setting to Enable or

Disable

remote access. If Enabled is selected,

you can select a Remote Access type.

USB Conﬁ guration

This screen will display the module version and all USB enabled devices.

Legacy USB Support

Select "Enabled" to enable the support for USB Legacy. Disable Legacy support

if there are no USB devices installed in the system. The options are

Enabled

and Disabled.

USB 2.0 Controller Mode

Select the controller mode for your USB ports. Options are HiSpeed and

FullSpeed

. (HiSpeed=480 Mbps, FullSpeed=12 Mbps

)

BIOS EHCI Hand-Off

Enable

or Disable a workaround for OS's without EHCI hand-off support.

System Health Monitor

CPU Overheat Temperature

Use the "+" and "-" keys to set the CPU temperature threshold to between 65

and 90

C. When this threshold is exceeded, the overheat LED on the chas-

sis will light up and an alarm will sound. The LED and alarm will turn off once

the CPU temperature has dropped to 5 degrees below the threshold set. The

default setting is

The other items in the submenu are all systems monitor displays for the follow-

ing information:

CPU1 Temperature, CPU2 Temperature (for dual CPU systems), System Tem-

perature, CPU1 Vcore, CPU2 Vcore (for dual CPU systems), +5 Vin, +12Vin,

-12V Vcc, DDRA VTT, DDRB VTT, 1.2V for Hyper-Transport, 2.5V, 5V standby,

2.5V standby and battery voltage.

Содержание AS-1020P-8R









































































































Результаты поиска

Содержание AS-1020P-8R

Отзывы:

Похожие инструкции для AS-1020P-8R

Бренды по названию

Популярные бренды

Supermicro AS-1020P-8R, Руководство пользователя

Результаты поиска

Содержание AS-1020P-8R

Отзывы:

Похожие инструкции для AS-1020P-8R

Бренды по названию

Популярные бренды