Supermicro AS-1020P-8R Скачать руководство пользователя страница 13

Страница: 13 / 104

1-3

Chapter 1: Introduction

COM port, a VGA (monitor) port, two USB 2.0 ports, PS/2 mouse and keyboard

ports and two gigabit Ethernet ports.

ATI Graphics Controller

The H8DSP-i/H8DSP-8 features an integrated ATI video controller based on the

Rage XL graphics chip. Rage XL fully supports sideband addressing and AGP

texturing. This onboard graphics package can provide a bandwidth of up to 512

MB/sec over a 32-bit graphics memory bus.

Other Features

Other onboard features that promote system health include onboard voltage moni-

tors, a chassis intrusion header, auto-switching voltage regulators, chassis and CPU

overheat sensors, virus protection and BIOS rescue.

1-3 Server

Chassis

Features

The 1020P-T(R)/1020P-8(R) is a high-end, scaleable server platform built upon

the SC816T-(R)700/SC816S-(R)700 1U server chassis. The following is a general

outline of the main features of the SC816T-(R)700/SC816S-(R)700 chassis.

System Power

1020P-T/1020P-8: the SC816T-700/SC816S-700 features a single 700W cold-swap

power supply. Power must be removed from the system before servicing or replac-

ing the power supply.

1020P-TR/1020P-8R: the SC816T-R700/SC816S-R700 features a redundant 700W

hot-swap power supply that consists of two power modules. One power supply

module will take over if the other fails. The hot-swap capability allows you to replace

a failed power supply module without having to power down the system.

SATA/SCSI Subsystem

The SC816T-(R)700/SC816S-(R)700 chassis was designed to support four SATA/

SCSI hard drives, which are hot-swappable units.

Note:

The operating system you use must have RAID support to enable the hot-

swap capability of the SATA/SCSI drives.

Содержание AS-1020P-8R









































































































Результаты поиска

Содержание AS-1020P-8R

Отзывы:

Похожие инструкции для AS-1020P-8R

Бренды по названию

Популярные бренды

Supermicro AS-1020P-8R, Руководство пользователя

Результаты поиска

Содержание AS-1020P-8R

Отзывы:

Похожие инструкции для AS-1020P-8R

Бренды по названию

Популярные бренды