Supermicro AS-1020P-8R Скачать руководство пользователя страница 12

Страница: 12 / 104

1-2

AS1020P-T(R)/1020P-8(R) User's Manual

1-2 Serverboard

Features

At the heart of the 1020P-T(R)/1020P-8(R) lies the H8DSP-i/H8DSP-8, a dual

processor serverboard based on Serverworks' HT-2000/1000 chipset. Below are

the main features of the H8DSP-i/H8DSP-8 (see Figure 1-1 for a block diagram

of the chipset).

Processors

The H8DSP-i/H8DSP-8 single or dual AMD Opteron 200 series 64-bit processors in

940-pin microPGA ZIF sockets. Please refer to the serverboard description pages

on our web site for a complete listing of supported processors.

Memory

The H8DSP-i/H8DSP-8 has eight 184-pin DIMM sockets that can support up to 32

GB of registered ECC DDR266/200 or up to 16 GB of registered ECC DDR400/333

SDRAM. (The maximum memory supported is halved if only one processor is

installed.) Memory in supported in both interleaved and non-interleaved conﬁ gura-

tions. See Section 5-6 for details.

Serial ATA [1020P-T(R)]

An SATA controller is integrated into the ServerWorks HT1000 chipset to provide

a four-port Serial ATA subsystem, which is RAID 0 and 1 supported. The SATA

drives are hot-swappable units.

Notes:

The operating system you use must have RAID support to enable the hot-

swap capability and RAID function of the Serial ATA drives.

SCSI [1020P-8(R)]

An Adaptec AIC-7902 SCSI controller is included on the H8DS8 to provide a four-

port dual-channel SCSI subsystem, which supports RAID 0, 1, 10 and JBOD. The

SCSI drives are hot-swappable units.

Notes:

The operating system you use must have RAID support to enable the

hot-swap capability and RAID function of the SCSI drives. The system supports

Zero Channel RAID (ZCR) with an AOC-LPZCR1 card (not included).

Onboard Controllers/Ports

One ﬂ oppy drive controller and two-channel ATA/100 are provided to support up

to four IDE hard drives or ATAPI devices. The color-coded I/O ports include one

Содержание AS-1020P-8R









































































































Результаты поиска

Содержание AS-1020P-8R

Отзывы:

Похожие инструкции для AS-1020P-8R

Бренды по названию

Популярные бренды

Supermicro AS-1020P-8R, Руководство пользователя

Результаты поиска

Содержание AS-1020P-8R

Отзывы:

Похожие инструкции для AS-1020P-8R

Бренды по названию

Популярные бренды