Supermicro AS-1020P-8R Скачать руководство пользователя страница 27

Страница: 27 / 104

Chapter 3: System Interface

3-1

Chapter 3

System Interface

3-1 Overview

There are several LEDs on the chassis control panel as well as others on the SATA

and SCSI drive carriers to keep you constantly informed of the overall status of the

system as well as the activity and health of speciﬁ c components. There are also

two buttons on the chassis control panel. This chapter explains the meanings of

all LED indicators and the appropriate response you may need to take.

3-2 Control

Panel

Buttons

There are two push-button buttons located on the front of the chassis. These are

(in order from left to right) a UID button and a power on/off button.

UID:

Depressing the UID (unit identiﬁ er) button illuminates an LED on both

the front and rear of the chassis for easy system location in large stack conﬁ gura-

tions (see Chapter 5). The LED will remain on until the button is pushed a second

time. Another UID button on the rear of the chassis serves the same function.

POWER:

This is the main power switch, which is used to apply or turn off

the main system power. Turning off system power with this button removes the

main power but keeps standby power supplied to the system.

Содержание AS-1020P-8R









































































































Результаты поиска

Содержание AS-1020P-8R

Отзывы:

Похожие инструкции для AS-1020P-8R

Бренды по названию

Популярные бренды

Supermicro AS-1020P-8R, Руководство пользователя

Результаты поиска

Содержание AS-1020P-8R

Отзывы:

Похожие инструкции для AS-1020P-8R

Бренды по названию

Популярные бренды