Supermicro AS-1020P-8R Скачать руководство пользователя страница 79

Страница: 79 / 104

Chapter 7: BIOS

7-7

Headless Mode

Select "Enabled" to activate the Headless Operation Mode through ACPI.

The options are Enabled and

Disabled

Event Log Conﬁ guration

View Event Log

Highlight this item and press <Enter> to view the contents of the event log.

Mark All Events as Read

Highlight this item and press <Enter> to mark the DMI events as read.

Clear Event Log

This setting will clear all event logs when set to "OK". The options are OK and

Cancel

Event Log Statistics

Highlight this item and press <Enter> to view details on the count of total unread

events.

Hyper Transport Conﬁ guration

CPU0: CPU1 HT Link Speed

The HT link will run at the speed speciﬁ ed in this setting if it is slower than or

equal to the system clock and if the board is capable. Options are

Auto

, 200

MHz, 400 MHz, 600 MHz, 800 MHz and 1 GHz.

ACPI APIC Support

Select "Enabled" to allow the ACPI APIC Table Pointer to be included in the

RSDT pointer list. The options are

Enabled

and Disabled.

ACPI OEMB Table

This setting when enabled will include an OEMB table pointer to pointer lists.

Options are

Enabled

and Disabled.

Содержание AS-1020P-8R









































































































Результаты поиска

Содержание AS-1020P-8R

Отзывы:

Похожие инструкции для AS-1020P-8R

Бренды по названию

Популярные бренды

Supermicro AS-1020P-8R, Руководство пользователя

Результаты поиска

Содержание AS-1020P-8R

Отзывы:

Похожие инструкции для AS-1020P-8R

Бренды по названию

Популярные бренды