Supermicro AS-1020P-8R Скачать руководство пользователя страница 3

Страница: 3 / 104

iii

Preface

Preface

About This Manual

This manual is written for professional system integrators and PC technicians. It

provides information for the installation and use of the AS1020P-T, 1020P-TR,

1020P-8 and 1020P-8R. Installation and maintainance should be performed by

experienced technicians only.

The 1020P-T(R)/1020P-8(R) is a high-end server based on the SC816T-(R)700/

SC816S-(R)700 1U rackmount chassis and the H8DSP-i/H8DSP-8, a dual proces-

sor serverboard that supports single or dual AMD Opteron

™

200 series proces-

sors and up to 32 GB of registered ECC DDR266/200 or 16 GB of registered ECC

DDR400/333 SDRAM memory. Please refer to the serverboard speciﬁ cations

pages on our web site for updates on supported processors (http://www.supermicro.

com/aplus/).

Manual Organization

Chapter 1: Introduction

The ﬁ rst chapter provides a checklist of the main components included with

the server system and describes the main features of the H8DSP-i/H8DSP-8

serverboard and the SC816T-(R)700/SC816S-(R)700 chassis, which comprise the

1020P-T(R)/1020P-8(R).

Chapter 2: Server Installation

This chapter describes the steps necessary to install the 1020P-T(R)/1020P-8(R)

into a rack and check out the server conﬁ guration prior to powering up the system.

If your server was ordered without processor and memory components, this chapter

will refer you to the appropriate sections of the manual for their installation.

Chapter 3: System Interface

Refer here for details on the system interface, which includes the functions and

information provided by the control panel on the chassis as well as other LEDs

located throughout the system.

Содержание AS-1020P-8R









































































































Результаты поиска

Содержание AS-1020P-8R

Отзывы:

Похожие инструкции для AS-1020P-8R

Бренды по названию

Популярные бренды

Supermicro AS-1020P-8R, Руководство пользователя

Результаты поиска

Содержание AS-1020P-8R

Отзывы:

Похожие инструкции для AS-1020P-8R

Бренды по названию

Популярные бренды