Supermicro AS-1020P-8R Скачать руководство пользователя страница 66

Страница: 66 / 104

6-4

AS1020P-T(R)/1020P-8(R) User's Manual

Figure 6-2. Removing a Fan

6-4 Drive

Bay

Installation/Removal

Accessing the Drive Bays

SATA and SCSI Drives: Because of their hotswap capability, you do not need to

access the inside of the chassis or power down the system to install or replace

SATA or SCSI drives. Proceed to the next step for instructions.

Note:

You must use standard 1" high, SATA/SCSI drives in the 1020P-T(R)/1020P-

8(R).

DVD/CD-ROM/Floppy Disk Drives: For installing/removing a DVD/CD-ROM or

ﬂ oppy disk drive, you will need to gain access to the inside of the system by remov-

ing the top cover of the chassis. Proceed to the "DVD/CD-ROM and Floppy Drive

Installation" section later in this chapter for instructions.

Note:

Only "slim" DVD/CD-ROM and ﬂ oppy drives will ﬁ t into the 1020P-T(R)/

1020P-8(R). The procedures for installing and removing SATA [1020P-T(R)] and

SCSI [1020P-8(R)] drives are the same.

Содержание AS-1020P-8R









































































































Результаты поиска

Содержание AS-1020P-8R

Отзывы:

Похожие инструкции для AS-1020P-8R

Бренды по названию

Популярные бренды

Supermicro AS-1020P-8R, Руководство пользователя

Результаты поиска

Содержание AS-1020P-8R

Отзывы:

Похожие инструкции для AS-1020P-8R

Бренды по названию

Популярные бренды