Supermicro AS-1020P-8R Скачать руководство пользователя страница 51

Страница: 51 / 104

Chapter 5: Advanced Serverboard Setup

5-17

ATX PS/2 Keyboard and
PS/2 Mouse Ports

The ATX PS/2 keyboard and the PS/2

mouse ports are located between the

COM1 and the LAN ports. See the

table on the right for pin deﬁ nitions.

Power LED/Speaker

On JD1, pins 1, 2, and 3 are for the

power LED and pins 4 through 7 are

for the speaker. See the tables on the

right for pin deﬁ nitions.

Note:

The speaker connector pins are

for use with an external speaker. If

you wish to use the onboard speaker,

you should close pins 6 and 7 with a

jumper.

Speaker Connector

Pin Deﬁ nitions (JD1)

Pin# Deﬁ nition

Red wire, Speaker data

No connection

Buzzer signal

Speaker data

PWR LED Connector

Pin Deﬁ nitions (JD1)

Pin# Deﬁ nition

+Vcc

-Vcc

PS/2 Keyboard and Mouse Port

Pin Deﬁ nitions

(KB/Mouse)

Pin # Deﬁ nition

Data

VCC

Clock

Ground

IPMB Header

The Intelligent Platform Management

Bus (IPMB) header is located at J22.

Connect the appropriate cable here to

utilize IPMB on your system. See the

table on the right for pin deﬁ nitions.

IPMB

Pin Deﬁ nitions (J22)

Pin# Deﬁ nition

Data

Ground

Clock

N/A

JLAN1/2 (Ethernet Ports)

Two Gigabit Ethernet ports (desig-

nated JLAN1 and JLAN2) are located

beside the VGA port. These ports

accept RJ45 type cables.

Содержание AS-1020P-8R









































































































Результаты поиска

Содержание AS-1020P-8R

Отзывы:

Похожие инструкции для AS-1020P-8R

Бренды по названию

Популярные бренды

Supermicro AS-1020P-8R, Руководство пользователя

Результаты поиска

Содержание AS-1020P-8R

Отзывы:

Похожие инструкции для AS-1020P-8R

Бренды по названию

Популярные бренды