Superior Fireplaces MHD 35 Series Скачать руководство пользователя страница 4

Страница: 4 / 72

General Information
900414-00 12/2015

Innovative Hearth Products
MHD 35/40 Series Direct-Vent Gas Fireplaces

THANK YOU FOR YOUR PURCHASE. WE APPRECIATE YOUR BUSINESS!

Please carefully read and follow all instructions in this manual. Pay special attention to all warnings and safety

information. Following these safety, care, and operation instructions will help ensure many years of dependable and

enjoyable service from your fireplace.

Please read and understand these instructions before installing,

operating, or servicing this product.

We recommend that our

gas hearth products be

installed and serviced by

professionals who are

certified in the U.S. by the

National Fireplace Institute®

(NFI) as NFI Gas Specialists.

General Information

Safety and Your Fireplace ..................................................................

Important Safety Information ............................................................

Fireplace Installation, Operation, and Maintenance Notices ...............

Packaging ..........................................................................................

Introduction .......................................................................................

Gas Pressure .....................................................................................

Requirements for the Commonwealth of Massachusetts ................

Cold Climate Insulation ....................................................................

Manufactured Home Requirements .................................................

Location ...........................................................................................

Vent Termination Clearances ...........................................................

Minimum Clearances to Combustibles ............................................

Wall Finishes / Surrounds / Mantels ................................................

Installation Preparation ....................................................................

Installation

Installation Sequence ......................................................................

Construct the Fireplace Framing ......................................................

Prepare the Fireplace Top Spacers ...................................................

Route the Gas Supply Line to the Fireplace .....................................

Determine Vent Setup in the Combination Venting Unit ...................

Install Metal, Non-Combustible Front Standoff for 40” Models Only ....

Rough in the Electrical Supply, if Needed ........................................

Install the [Optional] Blower Kit .......................................................

Place the Fireplace in the Framing and Secure ................................

Vent System ....................................................................................

Connect the Gas Line .......................................................................

Verify Proper Fireplace Operation ....................................................

Firebox Liners ..................................................................................

Install the Logs, Volcanic Stone, and Glowing Embers ....................

Install the Glass Door and Replace the Barrier ................................

Adjust the Air Shutter to Ensure Proper Flame Appearance .............

Install the Hood ...............................................................................

Reinstall the Included Barrier ..........................................................

Install the Finishing Materials ..........................................................

Attach the Safety-in-Operation Warnings.........................................

Installing Batteries in Remote Receiver and Wall Switch .................

Installation Accessories ...................................................................

Gas Conversion Kits ........................................................................

Operation

Operation .........................................................................................

Maintenance ....................................................................................

Accessory Components ...................................................................

Lighting Instructions .......................................................................

Troubleshooting ...............................................................................

Replacement Parts ..........................................................................

Warranty ..........................................................................................

Содержание MHD 35 Series









































































Результаты поиска

Содержание MHD 35 Series

Отзывы:

Похожие инструкции для MHD 35 Series

Бренды по названию

Популярные бренды

Superior Fireplaces MHD 35 Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание MHD 35 Series

Отзывы:

Похожие инструкции для MHD 35 Series

Бренды по названию

Популярные бренды