background image

Operation 

900414-00 12/2015

Innovative Hearth Products

 

MHD 35/40 Series Direct-Vent Gas Fireplaces

67

TROUBLESHOOTING

Before troubleshooting, ensure that the fireplace main line gas shutoff valve and the wall switch are in the ON position. The following 

troubleshoots the fireplace only to an elementary level. For detailed remote and ignition system troubleshooting, refer to the 

instructions provided with the remote.
Detailed valve system troubleshooting should only be performed by a qualified service technician.

Table 49 - Troubleshooting Millivolt Systems

SYMPTOM

POSSIBLE CAUSES

CORRECTIVE ACTION

1. 

Spark igniter will 

not light pilot after 

repeated triggering of 

igniter button.
WARNING: if the 

pilot will not light 

after 1 minute of 

attempting, wait for 

at least 5 minutes for 

gas to clear before 

attempting again.

a. 

Defective igniter (no spark at electrode).

Check for spark at electrode and pilot; if no spark and 

electrode wire is properly connected, replace igniter.

b. 

Defective or misaligned electrode at pilot 

(spark at electrode).

Using a match, light pilot. If pilot lights, turn off pilot 

and trigger the igniter button again. If pilot lights, an 

improper gas mixture caused the bad lighting and 

a  longer purge period is recommended. If pilot will 

not light – check gap at electrode and pilot – should 

be 1/8” to have a strong spark. If gap measures 1/8”, 

replace pilot.

c. 

Gas supply pressure errant.

Check inlet gas pressure. It should be within the limits 

as marked on the rating plate.

d. 

Pilot orifice plugged.

Clean or replace pilot orifice.

2. 

Pilot will not stay 

lit after carefully 

following the lighting 

instructions.

a. 

Defective pilot generator (thermocouple). Check pilot flame, it must impinge on thermocouple. 

Clean and/or adjust pilot for maximum flame 

impingement on thermocouple. Ensure that the 

connection between the valve and thermocouple are 

tight and secure.

3. 

Pilot burning, no 

gas to burner, Valve 

knob “ON,” and the 

(standard) burner 

OFF/ON switch is ON.

NOTE: 

If an optional* 

remote switch is used 

for burner operation, 

if the standard burner 

OFF/ON switch is still 

installed on fireplace 

it must be in the OFF 

position.

a. 

Wall switch or wires defective.

Check wall switch and wires for proper connections. 

Jumper wire across terminals at wall switch, if burner 

comes on, replace defective wall switch. If okay, 

jumper wires across wall switch wires at valve, if 

burner comes on, wires are faulty or connections are 

bad.

b. 

Thermopile may not be generating 

sufficient millivolts.

Check thermopile with millivolt meter. Take reading at 

thermopile terminals of gas valve. Should read 325 

millivolts minimum with optional wall switch OFF. 

Replace faulty thermopile if reading is below specified 

minimum.

c. 

Plugged burner orifice.

Check burner orifice for blockage and remove.

d. 

OFF/ON Switch and *Remote Switch are 

in the “ON” position resulting in excessive 

resistance.

When turning on the burner using a *remote switch, 

ensure that the standard OFF/ON switch is in the OFF 

position. If both switches are in the ON  position, 

it may result in excessive resistance (and millivolt 

drainage) and the burner may not come on.

4. 

Frequent pilot/burner 

outage problem.

a. 

Pilot flame may be too low or blowing 

(high) causing the pilot/valve safety to 

drop out.

Clean and/or adjust pilot flame for maximum flame 

impingement on thermocouple

* Optional remote switch kits—wall switch, wall thermostat or remote control.

Содержание MHD 35 Series









































































Отзывы: