Superior Fireplaces MHD 35 Series Скачать руководство пользователя страница 28

Страница: 28 / 72

Installation

900414-00 12/2015

Innovative Hearth Products
MHD 35/40 Series Direct-Vent Gas Fireplaces

Vertical Vent Figures/Tables

NOTE:

Secure Vent

rigid vent pipe is shown in the figures; Secure Flex

flexible vent pipe may also be used.

NOTE:

Rise per foot run ratios are acceptable all the way to level. For best results, maintain the horizontal/inclined

run in a straight (no dips), slightly elevated plane of approximately 1/4” per 1 ft (20 mm per 1 m).

NOTE:

SV4.5VF (Secure Vent), SF4.5VF (Secure Flex) firestop/spacer must be used anytime vent pipe passes

through a combustible floor or ceiling. SV4.5HF (Secure Vent), SF4.5HF (Secure Flex)firestop/spacer must be used

anytime vent pipe passes through a combustible wall.

NOTE:

Two (2) 45° elbows may be used in place of one (1) 90° elbow. The same rise to run ratios, as shown in the

venting figures for 90° elbows, must be followed if 45° elbows are used.

WARNING

Do NOT join separate sections of concentric flexible vent pipe.

Figure 28 - Top Vent—Straight

Table 16 - Rear Vent—One 90° Elbow

Ceiling

firestop/

spacer

SV4.5VF *

When using

Secure Flex

use ceiling

firestop/spacer

SF4.5VF.

60 ft (18.3 m)

maximum

Ceiling firestop/

spacer SV4.5VF *

When using Secure Flex

use ceiling firestop/spacer

SF4.5VF.

H Maximum

V Minimum

feet

meters

feet

meters

0.610

0.305

1.219

0.610

1.829

0.914

2.438

1.219

Install the U-shaped vent restrictor in any vent run with more than 6

ft of vertical rise. See

Page 21

for more information.

Minimum 6 ft and maximum of 60 ft of vertical venting.

V + H = 60 ft (18.3 m) maximum
H = 8 ft (2.4 m) maximum
Install the U-shaped vent restrictor in any vent run with more than

6 ft of vertical rise. See

Page 21

for more information.

If 8 ft of (H) horizontal vent run is needed, then 4 ft

(straight section) minimum of (V) vertical vent will be

required.
This table shows a 1 (V) to 2 (H) ratio. For every 1 ft of

(V) vertical, you are allowed 2 ft of (H) horizontal run,

up to a maximum horizontal run of 8 ft.
Minimum 6 ft of vertical venting.

Содержание MHD 35 Series









































































Результаты поиска

Содержание MHD 35 Series

Отзывы:

Похожие инструкции для MHD 35 Series

Бренды по названию

Популярные бренды

Superior Fireplaces MHD 35 Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание MHD 35 Series

Отзывы:

Похожие инструкции для MHD 35 Series

Бренды по названию

Популярные бренды