Superior Fireplaces MHD 35 Series Скачать руководство пользователя страница 42

Страница: 42 / 72

Installation

900414-00 12/2015

Innovative Hearth Products
MHD 35/40 Series Direct-Vent Gas Fireplaces

Light the fireplace. Follow the lighting procedure on the lighting label in the control compartment or

Page 65

Allow the burner to operate for at least fifteen (15) minutes while observing the flame continuously to ensure that

the proper flame appearance is achieved

(

Figure 40

)

. If the following conditions are present, adjust accordingly.

• If flame appears weak or sooty, adjust the air shutter, incrementally, to a more open position until the proper

flame appearance is achieved.

• If flame remains blue, adjust the air shutter, incrementally, to a more closed position until the proper flame

appearance is achieved.

When satisfied that the burner flame appearance is normal, reinstall the lower control compartment door, then

proceed to finish the installation.

Figure 40 - Fireplaces Flame Appearance

Table 29 - Main Burner Shutter Opening—Factory Setting

Models

Natural Gas

Propane

All

1/16”

(2 mm)

1/8”

(4 mm)

20.

Install the Hood

NOTE:

All models must have a hood installed prior to operation.

Install the hood by sliding it into the slots on the lower edge of the cabinet top.

NOTE:

To install the non-combustible finish material flush with the top of the hood, the hood must be installed before

installing the finish material. If finish material is installed flush with the top edge of the hood, the hood cannot be

removed.

NOTE:

To install the hood after installing the non-combustible finish material over the black surface above the

fireplace opening, the bottom edge of the finish material must be 5/8” above the top edge of the hood to allow

clearance for installation and removal of the hood.

21.

Reinstall the Included Barrier

WARNING

Reinstall any barrier removed before operating the fireplace. The barrier is designed to

reduce the risk of burns from hot glass. Do not operate the fireplace without the barrier

installed.

NOTE:

All models must have a barrier installed prior to operation.

Содержание MHD 35 Series









































































Результаты поиска

Содержание MHD 35 Series

Отзывы:

Похожие инструкции для MHD 35 Series

Бренды по названию

Популярные бренды

Superior Fireplaces MHD 35 Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание MHD 35 Series

Отзывы:

Похожие инструкции для MHD 35 Series

Бренды по названию

Популярные бренды