Superior Fireplaces MHD 35 Series Скачать руководство пользователя страница 26

Страница: 26 / 72

Installation

900414-00 12/2015

Innovative Hearth Products
MHD 35/40 Series Direct-Vent Gas Fireplaces

Figure 23 - Framing the ceiling opening

Figure 24 - Rear vent gasket

minimum 10 1/2 in.

(267 mm)

minimum 10 1/2 in.

(267 mm)

Roof

Framing

Ceiling

Framing

Plumb Bob

10-1/2” (267 mm) minimum

10-1/2” (267 mm)

minimum

Gasket

3. Install the rear vent gasket

—The rear vent gasket (Catalog no. F2116) is factory installed and required for

all rear vent applications. If the gasket is missing, position a replacement gasket around the vent collar before

attaching other vent components to the fireplace

(

Figure 24

)

. Loosely attach the gasket with two screws at the

top and bottom.

4. Attach the vent components to the fireplace

—See

Connecting the vent pipe on

Page 22

5. Attach the vent components to each other

—See

Connecting the vent pipe on

Page 22

6. Install firestop/spacer at ceiling

—When using Secure Vent

, use SV4.5VF firestop/spacer at ceiling joists; when

using Secure Flex

, use SF4.5VF firestop/spacer. If there is living space above the ceiling level, the firestop/

spacer must be installed on the bottom side of the ceiling. If attic space is above the ceiling, the firestop/spacer

must be installed on the top side of the joist. Route the vent sections through the framed opening and secure the

firestop/spacer with 8d nails or other appropriate fasteners at each corner.
Remember to maintain 1” (26 mm) clearance to combustibles, framing members, and attic or ceiling insulation

when running vertical chimney sections. The gap between the vent pipe and a vertical firestop can be sealed with

non-combustible caulking.

NOTE: Attic Insulation Shield (H3907)

must be installed when blown or loose-fill insulation is used, and is

required for all attic installations.

7. Support the vertical vent run sections

—Support the vertical portion of the venting system every 8 ft (2.4 m)

above the fireplace vent outlet. One method of support is by utilizing field provided support straps (conventional

plumber’s tape). Secure the plumber’s tape to the framing members with nails or screws. Loop the tape around

the vent, securing the ends of the tape to the framing. If desired, sheet metal screws #6 x 1/2” length may be

used to secure the support straps to the vent pipe

(

Figure 25

NOTE:

Proper venting support is very important.

Figure 25 - Supporting the Vertical Vent Run

Blocking

Support straps

(plumber’s tape)

8 ft (2.4 m)

maximum

1/2” (12.7

mm) minimum

clearance to

combustibles

8. Change vent direction of horizontal/inclined run

—Install the SV4.5E45 and SV4.5E90 elbows in the same

manner as the straight vent sections. See

Vent elbows on

Page 22

for more information.

Содержание MHD 35 Series









































































Результаты поиска

Содержание MHD 35 Series

Отзывы:

Похожие инструкции для MHD 35 Series

Бренды по названию

Популярные бренды

Superior Fireplaces MHD 35 Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание MHD 35 Series

Отзывы:

Похожие инструкции для MHD 35 Series

Бренды по названию

Популярные бренды