Superior Fireplaces MHD 35 Series Скачать руководство пользователя страница 57

Страница: 57 / 72

Operation

900414-00 12/2015

Innovative Hearth Products

MHD 35/40 Series Direct-Vent Gas Fireplaces

Installing and removing the glass door

WARNING

• Do not attempt to substitute the materials used on these doors, or replace cracked or broken glass.
• Handle this glass with extreme care! Glass is susceptible to damage—Do not scratch or handle roughly

while reinstalling the glass door frame.

• The glass door of this appliance must only be replaced as a complete unit as provided by the

manufacturer. Do not attempt to replace broken, cracked or chipped glass separately.

• Do not attempt to touch the front enclosure glass with your hands while the fireplace is in use.

WARNING

A barrier designed to reduce the risk of burns from the hot viewing glass is provided with this appliance and

shall be installed.

WARNING

Une barrière conçue pour réduire le risque de brûlure par le hublot chaude est fournie avec l’appareil et doit

être installé.

WARNING

Do not operate appliance with the glass front removed, cracked, or broken.

AVERTISSEMENT

Ne pas utiliser l’appareil si le panneau frontal en verre n’est pas en place, est craqué, ou brisé.

WARNING

Any safety screen, guard or barrier removed for servicing an appliance must be replaced prior to operating

the appliance.

AVERTISSEMENT

Tout écran ou protecteur retiré pour permettre l’entretien de l’appareil doit être remis en place avant de

mettre l’appareil en marche.

Only doors certified with the fireplace shall be used.

Seules des portes certifiées pour cet appareil doivent être utilisées.

WARNING

Do NOT abuse the glass door by striking it or slamming it shut.

Содержание MHD 35 Series









































































Результаты поиска

Содержание MHD 35 Series

Отзывы:

Похожие инструкции для MHD 35 Series

Бренды по названию

Популярные бренды

Superior Fireplaces MHD 35 Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание MHD 35 Series

Отзывы:

Похожие инструкции для MHD 35 Series

Бренды по названию

Популярные бренды