Superior Fireplaces MHD 35 Series Скачать руководство пользователя страница 33

Страница: 33 / 72

Installation

900414-00 12/2015

Innovative Hearth Products
MHD 35/40 Series Direct-Vent Gas Fireplaces

Table 20 - Venting Components Required for Various Exterior Wall Thicknesses, when using Typical Termination Kits

Vent Components Required

Exterior Wall Thickness

Termination Kit Only

6 to 9-1/4” (152 to 235 mm)

Termination Kit and 6” Vent Section (SV4.5L6)

10-3/4 to 14” (273 to 356 mm)

Termination Kit and 12” Vent Section (SV4.5L12)

16-3/4 to 20” (426 to 508 mm)

Termination Kit and Telescopic Section (SV4.5L12)

11-3/4 to 20” (299 to 508 mm)

Horizontal Vent Figures/Tables

NOTE:

Secure Vent

rigid vent pipe and terminal are shown in the figures. Secure Flex

flexible vent pipe and

terminal may also be used.

NOTE:

Two (2) 45° elbows may be used in place of one (1) 90° elbow. The same rise to run ratios, as shown in the

venting figures for 90° elbows, must be followed if 45° elbows are used.

NOTE:

Maintain the horizontal/inclined run in a straight (no dips), slightly elevated plane. The recommended incline

is approximately 1/4” per 1 ft (20 mm per 1 m) horizontal, in a direction away from the fireplace. Smaller rise per

foot run ratios are acceptable all the way to at or near level. Use a carpenter’s level to measure from a constant

surface and adjust the support straps as necessary.

NOTE:

SV4.5VF (Secure Vent), SF4.5VF (Secure Flex) firestop/spacer must be used any time vent pipe passes

through a combustible floor or ceiling. SV4.5HF (Secure Vent), SF4.5HF (Secure Flex) firestop/spacer must be used

any time vent pipe passes through a combustible wall.

WARNING

Do not join separate sections of concentric flexible vent together.

Table 21 - Rear Vent—No Elbows

See

Table 20

as an aid in venting component selection for a

particular range of exterior wall thicknesses.

Note: “H” is horizontal distance from rear of unit to outer wall

surface

Note:

When venting Rear Horizontal with slip collar and

termination only, install base vent restrictor with the

breakwway portion raised. On 33” Models, use the 3” base

at 6’ instead of the 2 1/2” breakaway.

H = 28 in. (711 mm) Maximum

When using

Secure Flex

, use

Wall Firestop/Spacer

SF4.5HF

When using Secure Flex

, use

wall firestop/spacer SF4.5HF, and

install venting with a minimum of

12” rise.

H = 21” (533 mm) maximum

27-1/2”

(699 mm) to outside

of termination

Table 22 - Top Vent—One 90° Elbow, Elbow Connection at Fireplace

H Maximum

V Minimum

Wall

firestop/

spacer

SV4.5HF *

When using Secure Flex

, use

wall firestop/spacer SF4.5HF.

feet

meters

feet

meters

0.91

Elbow only

Install the U-shaped vent restrictor in any vent run with more

than 4 ft of vertical rise. See

Page 21

for more information.

See

Table 20

as an aid in venting component selection for a

particular range of exterior wall thicknesses.
NOTE: Only in top vent where elbow is connected at fireplace collar

is it allowed to count elbow as 1 ft. vertical (V) rise.

Содержание MHD 35 Series









































































Результаты поиска

Содержание MHD 35 Series

Отзывы:

Похожие инструкции для MHD 35 Series

Бренды по названию

Популярные бренды

Superior Fireplaces MHD 35 Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание MHD 35 Series

Отзывы:

Похожие инструкции для MHD 35 Series

Бренды по названию

Популярные бренды