Superior Fireplaces MHD 35 Series Скачать руководство пользователя страница 1

Страница: 1 / 72

- Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any

other appliance.

- WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use

any phone in your building.

• Leave the building immediately.

• Immediately call your gas supplier from a neigh-

bor’s phone. Follow the gas supplier’s instruc-

tions.

• If you cannot reach your gas supplier, call the

fire department.

- Installation and service must be performed by

a qualified installer, service agency or the gas

supplier.

WARNING:
FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly could

result in serious injury, death, or property damage.

AVERTISSEMENT:
RISQUED’INDENDIE OU D’EXPLOSION

Le non-respect Des avertissements de sécurité

pourrait d’entraîner des blessures graves, la mort

ou des dommages matériels.

- Ne pas entreposer ni utilizer d’essence ni d’autres

vapeurs ou liquides inflammables dans le voisinage

de cet appareil ou de tout autre appareil.

- QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ:

• Ne pas tenter d’allumer d’appareil.

• Ne touchez à aucan interrupteur. Ne pas vous servir

des téléphones se trouvant dans le bâtiment où

vous trouvez.

• Sortez immédiatement de bâtiment.

• Appelez immédiatement votre fournisseur de

gaz depuis un voisin. Suivez les instructions du

fournisseur.

• Si vous ne pouvez rejoindre le fournisseur de gaz,

appelez le service des incindies.

- L’installation et l’entretien doivent être assurés par

un installateur ou un service d’entretien qualifié

ou par le fournisseur de gaz.

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future

reference.

Installateur : Laissez cette notice avec l’appareil.

Consommateur : Conservez cette notice pour

consultation ultérieure.

This appliance may be installed as an OEM installation in a manufactured home (USA only) or mobile home and

must be installed in accordance with the manufacturer’s instructions and the Manufactured Home Construction

and Safety Standard, Title 24 CFR, Part 3280, in the United States, or the Standard for Installation in Mobile

Homes, CAN/CSA Z240 MH, in Canada. This appliance is only for use with the type(s) of gas indicated on the

rating plate. A conversion kit is supplied with the appliance.
Cet appareil peut être installé comme du matériel d’origine dans une maison préfabriquée (É.-U. seulement)

ou mobile et doit être installé selon les instruc! ons du fabricant et conformément à la norme Manufactured

Home Construction and Safety Standard, Title 24 CFR, Part 3280 aux États-Unis ou à la norme CAN/CSA Z240

Série MM, Maisons mobiles au Canada. Cet appareil doit être u! lisé uniquement avec les types de gaz indi-

qués sur la plaque signalé! que. Une trousse de conversion est fournie avec l’appareil.

Installation and Operation Instructions

Models

PFS

Report No. F13-094

Ce manuel est disponible en francais, simplement

en faire la demande. Numéro de la pièce 900414-01.

P/N 900414-00 REV. C 12/2015

MHD 35/40 Series Direct-Vent Gas Fireplaces

MHD35DMN

MHD35DMP

MHD40DMN

MHD40DMP

P900414-00

Содержание MHD 35 Series









































































Результаты поиска

Содержание MHD 35 Series

Отзывы:

Похожие инструкции для MHD 35 Series

Бренды по названию

Популярные бренды

Superior Fireplaces MHD 35 Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание MHD 35 Series

Отзывы:

Похожие инструкции для MHD 35 Series

Бренды по названию

Популярные бренды