background image

10 Operation of LCD Display 

 

User Manual 

76  

 

10.10.4  Reactive Power Setting for Italy 

If the “Countries” selected is “IT” (Italy), several LCD menus and operation methods 
are different from other countries.   

The differences focus on “Run-param” as shown below. 

Italy “Q(P)” Mode 

Power factor changes with the output power of the 
inverter. 
 
Select  Q(P)  mode  and 

Press 

 

to enter into the 

“Run-para-Q(P)” sub-menu. 
 

Press 

 to move the cursor; 

Press 

 to enter the 

editing mode, then the selected parameter will be 
shaded. 

Press

 

 to increase one-step value; 

Press

 

 

to 

decrease one-step value. 

Press

 ENTER

 to confirm the setting and exit from the 

editing mode. 

 

Tab. 10-8

 

Italy “Q(P)” Mode Parameters Explanation 

Parameter 

Explanation

Default

Range

Step

PA* 

Active power at point A (in %)

20% 20~100% 

1% 

PB* 

Active power at point B (in %)

50% 20~100% 

1% 

PC* 

Active power at point C (in %)

100% 20~100% 

1% 

Pf max 

Power factor at point C 

0.9 

0.9~1 

0.01 

Uin** 

Enter Q(P) regulation mode 
when grid voltage is above 
Uin 

105% 100~110% 

1% 

Uout** 

Exit from the Q(P) regulation 
mode when grid voltage is 
below Uout 

100% 90~100% 

1% 

*PA < PB

  PC        ** Uin

Uout 

Содержание SG60KTL





































































































Отзывы: