Sungrow SG60KTL Скачать руководство пользователя страница 32

Страница: 32 / 100

5 Mechanical Installation

User Manual



Take enough space for convection into consideration when installing multiple

inverters. It is suggest to stagers the inverters.



Do not install the inverter in a confined space.

Inverter will not work normally if otherwise.



Install the inverter where children cannot reach.



Do not install the inverter near residential area.

Noise can be produced during inverter operation

which may affect the daily life.

5.2

Moving Inverter to Installation Site

To install the inverter, remove the inverter from the packaging and move it to the
installation site. Follow the instructions below during inverter moving:



Always keep in mind the weight of the inverter.



Lift the inverter by gasping the handles on two sides of the inverter.

Содержание SG60KTL





































































































Результаты поиска

Содержание SG60KTL

Отзывы:

Похожие инструкции для SG60KTL

Бренды по названию

Популярные бренды

Sungrow SG60KTL, Руководство пользователя

Результаты поиска

Содержание SG60KTL

Отзывы:

Похожие инструкции для SG60KTL

Бренды по названию

Популярные бренды