Sungrow SG60KTL Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 100

background image

1

1

Safety Instructions

The inverter has been designed and tested strictly according to the international
safety regulations. As electrical and electronic equipment, safety instructions related
to them must be complied with during installation, commissioning, operation and
maintenance. Incorrect operation or work may result in damage to:



The life and well-being of the operator or a third party



The inverter and other properties that belong to the operator or a third party

Therefore, the following general safety instructions must be read and always kept in
mind prior to any work. All detailed work-related safety warnings and notes will be
specified at the critical points in corresponding chapter.

All installations should be performed by technical personnel. They have:



received professional training;



read through this manual and understood all related safety instructions;



been familiar with electric system related safety instructions.

Technical personnel mentioned above may perform the following work:



Install the inverter onto the wall;



Connect the inverter to the PV system;



Commission the inverter;



Operate and maintain the inverter.

Before Installation

There is a risk of injury due to improperly handling the device!



Always follow the instructions in the manual when moving and
positioning the inverter.



Injuries, serious wounds, or bruise may follow if the device is improperly
handled.

«
...
9
10
11
12
13
...
»

Содержание SG60KTL





































































































Отзывы:

Нет отзывов

Похожие инструкции для SG60KTL

Бренд: U.S. Converters Страницы: 19

Бренд: MAER IDROPULITRICI Страницы: 13

Бренд: Bang & Olufsen Страницы: 12

Бренд: Planet Страницы: 36

Бренд: Velleman Страницы: 11

Бренд: Wagan Страницы: 11

Бренд: INVT Страницы: 174

SC-TDC-1000 D Series

Бренд: Surface Concept Страницы: 28

Бренд: Soarland & Hexin Страницы: 2

Бренд: EZIHEAT Страницы: 34

Argus 2000-0370-2

Бренд: Vela Страницы: 153

Бренд: Vela Страницы: 28

Бренд: wattsonic Страницы: 87

Бренд: StarTech.com Страницы: 2

Бренд: Audio Note Страницы: 11

Бренд: Samlex Europe Страницы: 52

Бренд: Quantum Harvest Страницы: 33

Бренд: Dataforth Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды