Sungrow SG60KTL Скачать руководство пользователя страница 59

Страница: 59 / 100

User Manual

7 Commissioning

Step 8

Set the inverter time as per local time.
Incorrect time setting will affect the data
logging.

Press



to move the cursor and

Press



to set the specific time and date.

Press

ENTER

to confirm setting.

Step 9

After configuring all parameters, there will be
a “setting confirmation” screen. Check whether
all above-mentioned parameters are correct.
Confirm by

Pressing

ENTER

. Cancel by

Pressing

ESC

and reset.

Step 10

Inverter will enter into startup process.
Observe the status of LED indicators and the
LCD main screen. If commissioning succeeds,
the “RUN” indicator will be on and “Run” will be
displayed on the “State” area.

If commissioning fails, the “FAULT” indicator will be on and “Fault” will occur on the
display.

Press



to view “current fault” information. Remove the existing fault and

then repeat the commissioning procedures.

Содержание SG60KTL





































































































Результаты поиска

Содержание SG60KTL

Отзывы:

Похожие инструкции для SG60KTL

Бренды по названию

Популярные бренды

Sungrow SG60KTL, Руководство пользователя

Результаты поиска

Содержание SG60KTL

Отзывы:

Похожие инструкции для SG60KTL

Бренды по названию

Популярные бренды