Sungrow SG60KTL Скачать руководство пользователя страница 68

Страница: 68 / 100

9 Troubleshooting and Maintenance

User Manual

Step 9

Press on the ribbing of the locking hooks
and pull the cable outwards.

Step 10

Remove the fans out of the inverter.

Step 11

Clean the fan with soft brush or vacuum cleaner; or replace the broken fans.

Step 12

Reassemble the fans back into the inverter and restart the inverter.

Cleaning Air Inlet and Outlet

A huge amount of heat is generated in the process of running the inverter. The
inverter adopts a controlled forced-air cooling method.

In order to maintain good ventilation, please check to make sure the air inlet and
outlet are not blocked.

Clean the air inlet and outlet with soft brush or vacuum cleaner if necessary.

9.3

Contact Sungrow Service

Should you have any problems in operating on the inverter, please contact us:

Service hotline: +86 551 65327817

Email:

[email protected]

(after-sales)

[email protected]

(technical support)

We need the following information to provide you the best assistance:



Type of the inverter

Содержание SG60KTL





































































































Результаты поиска

Содержание SG60KTL

Отзывы:

Похожие инструкции для SG60KTL

Бренды по названию

Популярные бренды

Sungrow SG60KTL, Руководство пользователя

Результаты поиска

Содержание SG60KTL

Отзывы:

Похожие инструкции для SG60KTL

Бренды по названию

Популярные бренды