Sun Microsystems Sun Fire V1280 Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 64

background image

A-2

Sun Fire V1280/Netra 1280 Systems Installation Guide • May 2006

A.1

I/O Slots

There are currently three versions of IB_SSC assemblies, PCI, PCI+, and PCI-X.
Consult your Sun representative for cards supported by your version of the IB_SSC
assembly.

Note –

Mixing PCI, PCI+ and PCI-X cards within an IB6 leaf (two slots) is not

recommended since leaf slots run at the lowest speed and the lowest mode for a
given set of cards within a leaf. For example, if a 66 MHz PCI card is in slot 0 and a
100 MHz PCI-X card is in slot 1, then both leaf slots will run at the lower 66 MHz
PCI speed. IB6 leafs are comprised of paired slots 0 and 1, 2 and 3, and 4 and 5.

A.1.1

PCI IB_SSC Assemblies

PCI IB_SSC assemblies provide six I/O slots labeled 0 through 5. When viewing the
rear of the system, slot 0 is on the left and slot 5 is on the right. Slot 0 supports 66
MHz, slots 1-5 support 33 MHz with 5V signaling. The I/O slots are

not

hot

swappable. All slots are half length.

Note –

PCI+ and PCI-X IB_SSC assemblies are not supported in Netra 1280 systems.

A.1.2

PCI+ and PCI-X IB_SSC Assemblies

Note –

PCI+ and PCI-X IB_SSC assemblies are not supported in Netra 1280 systems.

PCI+ and PCI-X IB_SSC assemblies provide six I/O slots labeled 0 through 5. When
viewing the rear of the system, slot 0 is on the left and slot 5 is on the right. All six
slots support up to 66 MHz. The I/O slots are

not

hot swappable, all slots are half

length and 5V signaling is not supported.

«
...
52
53
54
55
56
...
»

Содержание Sun Fire V1280

































































Отзывы:

Нет отзывов

Похожие инструкции для Sun Fire V1280

Бренд: Datacom Страницы: 89

SuperServer E301-9D-8CN8TP

Бренд: Supermicro Страницы: 117

SUPERSERVER 5028TK-HTR

Бренд: Supermicro Страницы: 138

Бренд: Gigabyte Страницы: 108

Бренд: Toshiba Страницы: 28

Бренд: Toshiba Страницы: 204

SD-H400 - Combination Progressive-Scan DVD Player

Бренд: Toshiba Страницы: 291

Бренд: Wyse Страницы: 2

Бренд: Supermicro Страницы: 96

Бренд: Supermicro Страницы: 130

Бренд: Supermicro Страницы: 124

Бренд: Blonder tongue Страницы: 20

Бренд: Gigafast Страницы: 74

SocketEthernetIP EN60601

Бренд: Multitech Страницы: 2

Бренд: LG-Ericsson Страницы: 54

Бренд: Vingtor Stentofon Страницы: 68

Бренд: IBM Страницы: 82

Бренд: IBM Страницы: 135

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды