Sun Microsystems Sun Fire V1280 Скачать руководство пользователя страница 14

Страница: 14 / 64

1-2

Sun Fire V1280/Netra 1280 Systems Installation Guide • May 2006

Caution –

The Sun Fire V1280/Netra 1280 system, with mounting cradle, weighs

approximately 286 lbs (130 kg). Two people using a computer equipment lift are
required to move the system safely into the cabinet .

Caution –

Pull only one Sun Fire V1280/Netra 1280 system out of the cabinet at a

time to prevent unbalancing the cabinet.

Caution –

The cabinet stabilizers (if applicable) must be extended whenever a Sun

Fire V1280/Netra 1280 system is pulled out of the cabinet.

1.1

Installing Slides and Rails

Systems received freestanding which are to be mounted in a cabinet are shipped
with a slide rail mounting kit. This kit includes the following:

■

Two slide lock spacers

■

Two slide lock nuts

■

Four rails, two inner and two outer

■

8 mm wrench

Note –

If you received your system pre-einstalled in a cabinet you may proceed

directly to

Section 1.4, “Installing the Cable Management Arm” on page 1-21

This section contains the following topics:

■

Section 1.1.1, “Adjusting the Rail Assembly” on page 1-3

■

Section 1.1.2, “Installing the Inner Slides on the System” on page 1-4

■

Section 1.1.3, “Preparing the Rails for Two-Post Installations” on page 1-6

■

Section 1.1.4, “Installing the Rail Assemblies in a Sun Fire/StoreEdge Cabinet” on
page 1-7

■

Section 1.1.5, “Installing the Rail Assemblies in a Sun Rack 900 Cabinet” on
page 1-9

■

Section 1.1.6, “Installing the Rail Assemblies in a 19-Inch Four-Post Cabinet” on
page 1-11

■

Section 1.1.7, “Installing the Rail Assemblies in a 19-inch Two-Post Rack” on
page 1-12

Содержание Sun Fire V1280

































































Результаты поиска

Содержание Sun Fire V1280

Отзывы:

Похожие инструкции для Sun Fire V1280

Бренды по названию

Популярные бренды

Sun Microsystems Sun Fire V1280, Руководство по установке

Результаты поиска

Содержание Sun Fire V1280

Отзывы:

Похожие инструкции для Sun Fire V1280

Бренды по названию

Популярные бренды