Sun Microsystems Sun Fire V1280 Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 64

background image

Chapter 1

Physical Installation

1-39

5. Turn off each external drive and expansion cabinet (as applicable).

6. Turn the power switch to the Standby position.

Caution –

The On/Standby power switch does not isolate the equipment. Turning

off the power switch on the customer-supplied circuit breakers is required to isolate
the equipment.

1.11

Installing Additional Hardware

Do not install additional hardware until the initial factory configuration has been
completely installed, the system has been powered on, and POST has been
completed successfully. This makes it easier to diagnose conflicts that might be
caused by additional installations.

Caution –

To avoid damaging boards when installing CPU/Memory boards refer to

the Sun Fire V1280/Netra 1280

Systems Service Manual

for instructions.

Caution –

During initial installation, turn off the power at the circuit breakers

before removing or replacing system hardware. Refer to the installation guide of the
additional hardware for any additional instructions.

Note –

For optimum performance, use only I/O cards and associated drivers that

are qualified by Sun Microsystems for use on the Sun Fire V1280/Netra 1280
systems. It is possible for interactions to occur between cards and drivers on a
specific bus that might lead to potential system panics or other negative outcomes if
the card/driver solution is not qualified by Sun Microsystems.

For an updated listing of qualified I/O cards and configurations for the system,
contact your Sun authorized sales representative or your service provider. For
additional information refer to:

http://www.sun.com/io

«
...
49
50
51
52
53
...
»

Содержание Sun Fire V1280

































































Отзывы:

Нет отзывов

Похожие инструкции для Sun Fire V1280

Бренд: Aastra Страницы: 592

6219 - IntelliStation M - Pro

Бренд: IBM Страницы: 317

CX PRINT SERVER 550

Бренд: Xerox Страницы: 166

AssuredSAN 4004 Series

Бренд: Dot Hill Страницы: 59

Бренд: IBM Страницы: 82

Бренд: DNP Страницы: 93

Бренд: IBM Страницы: 76

Бренд: Cisco Страницы: 40

LAN Brick Eth 10

Бренд: MPI Technologies Страницы: 2

Edgeline EL4000

Бренд: HPE Страницы: 57

ProLiant ML110 Gen10

Бренд: HPE Страницы: 101

ProLiant ML110 Gen10

Бренд: HPE Страницы: 159

Бренд: Promise Technology Страницы: 318

Бренд: Allnet Страницы: 91

Бренд: IBM Страницы: 2

Бренд: GIGA-BYTE TECHNOLOGY Страницы: 137

Бренд: D-Link Страницы: 146

Бренд: TROY Group Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды