Suez Sievers M500e Скачать руководство пользователя страница 57

Страница: 57 / 325

YSTEM

ESCRIPTION

.............................

Sievers M500e TOC Analyzer

Operation and Maintenance Manual

DLM 78510-02 EN Rev. B

DDITIONAL

YSTEM

OMPONENTS

Microprocessor Controller and Electronics

The M500e TOC Analyzer contains seven proprietary electronic board assemblies

which monitor and control Analyzer functions:

•

System board including a system on module CPU with ARM microprocessor, 4 GB

memory, 1 GB DDR RAM, non-volatile flash memory for operator settings, digital

input/output (I/O), display graphics controller, RS-232 (serial) port, interface-to-USB

memory devices, Ethernet port, and WiFi (optional).

•

Fan controller which controls three fans, one for thermal control, within the Analyzer

•

Passive interconnect board

•

Instrument controller I/O board with interfaces to pumps and motors, UV lamp,

external devices, via binary input, four alarms, and three 4-20 mA outputs

•

LED capacitive touch panel display and interface

•

Analog to digital conversion boards (2) with integrated signal conditioning circuits

for cell conductivity and temperature measurements

Data Outputs

The Sievers M500e TOC Analyzer offers three 4-20 mA outputs, four alarm outputs,

and two isolated binary (start/stop) inputs.The Analyzer also includes one serial

(RS

232), one USB, and one Ethernet output allowing flexibility for exporting and

printing data. Real-time and historical data can be transferred from the Analyzer via

Ethernet (using a communications software, such as Modbus or ProfiNet) or from the

serial port to a computer (using a communication software such as PuTTY. The

Analyzer also enables the use of a communications software (such as PuTTY) to

issue commands to the Analyzer via a serial (RS-232) or Ethernet connection. (For

more information, see

“Streaming Data” on page 297

NOTE:

The Analyzer’s USB port is designed for connection to a USB memory

device. The USB port does not support connectivity to a computer or printer.

Содержание Sievers M500e






































































































































































































































































































































Результаты поиска

Содержание Sievers M500e

Отзывы:

Бренды по названию

Популярные бренды

Suez Sievers M500e, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание Sievers M500e

Отзывы:

Бренды по названию

Популярные бренды