manualshive.com logo in svg

Stryker Operating Room Information System, Руководство по предварительной установке

Поделиться
Скачать
Stryker Operating Room Information System Скачать руководство пользователя страница 9

 

   

   

5

S

2.  Warnings and Cautions

Please read this manual and follow its instructions carefully. The words WARNING, CAUTION, and 

Note carry special meanings and should be carefully reviewed.

WARNING The personal safety of the patient or user may be involved. Disregarding 

this information could result in injury to the patient.

Caution

Special service procedures or precautions must be followed to avoid dam-

aging the instrument.

Note

Special information to make maintenance easier or important information more 

clear.

2.1   Warnings

To avoid potential serious injury to the user and the patient, the user must:

1.  Read this manual thoroughly, and be familiar with its contents prior to using this equipment.
2.  Be qualified physician/technician or medical personnel, having complete knowledge of the use 

of this equipment.

3.  Test this equipment prior to a surgical procedure. This product was fully tested at the factory 

before shipment.

4.  DO NOT remove covers on the product, to avoid an electric shock.
5.  DO NOT perform internal repairs or adjustments unless specifically instructed to do so in this 

manual.

6.  The electrical installation of relevant operating room equipment must comply with the appli-

cable IEC, CEC, and NEC requirements, and any other applicable international requirements 

where this product is sold. In the case where the information in this manual conflicts with local 

building/electrical regulations, local regulations will take precedence.

Содержание Operating Room Information System

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды