manualshive.com logo in svg

Stratus ftServer 2900 Series, Планирование и руководство по установке

Поделиться
Скачать
Stratus ftServer 2900 Series Скачать руководство пользователя страница 99

Installing the System Enclosures

Installing the System in a Cabinet

9-21

Installing the System Enclosures 

After you have installed the shelf unit (and reinstalled the system backplane assembly 
and the front panel), you must install the CPU-I/O enclosures and the bezel. 

1. Install the CPU-I/O enclosures.

a. Place each CPU-I/O enclosure on a flat surface and pull down the two ejector 

levers (number 1, shown in lower-left box in 

Figure 9-18

).

N O T E

If your shipment contains an operating system DVD, the 
operating system and system software were installed in 
one of the CPU-I/O enclosures at the factory. In this case, 
install the CPU-I/O enclosure that contains the boot disk 
(labeled “Boot”) in the top CPU-I/O slot.

b. With the ejector levers in the open (down) position, slide each CPU-I/O 

enclosure into the shelf unit. 

C A U T I O N

!

To avoid personal injury, lifting a CPU-I/O enclosure 
requires two persons. 

M I S E   E N   G A R D E

!

Pour éviter toute blessure, deux personnes sont requises 
pour soulever le boîtier CPU-I/O.

Содержание ftServer 2900 Series





















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды