Stratus ftServer 2900 Series Скачать руководство пользователя страница 46

Страница: 46 / 148

Ethernet Cables

4-6

Stratus ftServer 29x0, 49x0, and 69x0 Systems: Site Planning and Installation Guide

(R786)



From a management PC to a network connection point, for web management of
ftScalable Storage systems

The same network must provide access to the RAID controllers on the ftScalable
controller tray from the PC.

Table 4-4

describes the cables you must supply for network connectivity. Be sure to

provide cables of sufficient length for the distance between the system and a wall jack
or hub.

Table 4-4. Customer-Supplied Ethernet Cables

Component

Quantity

Cable Length

Cable Type

VTM Ethernet Port

N/A. You must supply
these cables.

The maximum
allowable distance
from these ports to a
switch or a hub is
328 ft (100m).

24 AWG Unshielded Twisted Pair
(UTP) EIA/TIA-Verified, Category-3
or Category-5 wire, with RJ-45
modular connectors terminated with
pair-wiring adhering to the EIA/TIA
568-A or EIA/TIA 568-B standard.

For connections to an Ethernet hub
or switch, provide a straight-through
cable.

For 100- or 1000-Mbps (fast
Ethernet) operation, provide
full-duplex, or Category-5 Ethernet
cables.

1GbE Embedded
Ethernet Port

U113 Dual-Port
10/100/1000
Base-T Ethernet
PCI-Express
Adapter (RJ-45
copper)

Ordered in
pairs.
Typically
teamed for
fault
tolerance.

The maximum
distance between the
adapter and a hub or a
switch is
328 ft (100m).

The customer must supply a
standard Ethernet cable to the
following specifications:

1000 Mbps requires a Category-5E
cable

100 Mbps (fast Ethernet
connection) requires either a
Category-5E (recommended) or
Category-5 cable

10 Mbps requires either a
Category-5, Category-4, or
Category-3 cable

Содержание ftServer 2900 Series





















































































































































Результаты поиска

Содержание ftServer 2900 Series

Отзывы:

Бренды по названию

Популярные бренды

Stratus ftServer 2900 Series, Планирование и руководство по установке

Результаты поиска

Содержание ftServer 2900 Series

Отзывы:

Бренды по названию

Популярные бренды