Stratus ftServer 2900 Series Скачать руководство пользователя страница 118

Страница: 118 / 148

Connecting Systems to Power Through PDUs

11-6

Stratus ftServer 29x0, 49x0, and 69x0 Systems: Site Planning and Installation Guide

(R786)

Connecting Systems to Power Through PDUs

N O T E

Do not connect a PDU or peripheral components to a
Stratus-qualified UPS, which is sized only for the ftServer
system.

1. From the front of the system, make sure that the CPU-I/O enclosures are fully

inserted into the shelf unit by tightening the thumbscrews, if necessary.

2. Locate two black power cables and two labels, A and B.

3. Connect the A-side and B-side PDUs to

separate

AC power sources. For each

PDU, do the following:

a. At the back of the cabinet, attach the IEC 320-C19 connector end of the

country-specific external power cord (number 5 in

Figure 11-3

) to the single

PDU inlet connector on the right side of the PDU.

b. Connect the country-specific connector end to a power source.

c. Attach the appropriate label to the power cable to indicate A- or B-side power.

Figure 11-3

shows how to connect PDUs to ftServer systems and directly to

power sources.

4. Locate one black and one gray power cable (

jumper

5. Connect the IEC-C13 end of the

gray

power cable (number 4) to the receptacle on

the top CPU-I/O enclosure. (Lift the small power-cord locking bar above the
receptacle to insert the power cord into the enclosure.) Connect the other end of
the gray cable to the

top

PDU.

6. Connect the IEC-C13 end of the

black

cable (number 3) to the receptacle on the

bottom CPU-I/O enclosure. Connect the other end of the black cable to the

bottom

PDU.

7. If applicable, repeat steps

through

for additional systems.

Figure 11-3

shows the color-coded power cords connected to the systems and PDUs.

Содержание ftServer 2900 Series





















































































































































Результаты поиска

Содержание ftServer 2900 Series

Отзывы:

Бренды по названию

Популярные бренды

Stratus ftServer 2900 Series, Планирование и руководство по установке

Результаты поиска

Содержание ftServer 2900 Series

Отзывы:

Бренды по названию

Популярные бренды