71
ENGLISH
EN
7.10.4 Checking the oil level in the hydrostat
See fig. 35.
1. Set up the hydrostat in a vise and remove the oil plug (H).
2. Check the oil level. The level shall be 25 mm under the
upper part of the hole at the temperature 10-38°C. Top up
as required.
Type of oil: Motor oil 5W-30.
3. Reassemble the oil plug and bleed the hydrostat
according to the instructions below.
7.10.5 Bleeding the hydrostat
1. Lock the by-pass valve in open position using a steel wire
or similar.
2. Fit a drilling machine with a suitable screw bit to the
pulley mounting screw.
3. Start carefully the drilling machine so the pulley rotates.
During this procedure, move the speed lever (J) 5 times
reciprocating between its end positions.
4. Run the drilling machine in the opposite direction so the
pulley rotates. During this procedure, move the speed
lever (J) 5 times reciprocating between its end positions.
5. Lock the by-pass valve in closed position and repeat steps
2-4 above.
6. Check the oil level again. Top up as required. If oil has to
be added, the bleeding in steps 1-5 must be repeated.
Note! The driving shaft rotates about twice as fast
forwards as backwards when driving with the drilling
machine.
7.11 REPLACING THE SHEAR BOLTS
(R IN FIG. 12)
The auger is fastened to the shaft by special bolts that are
designed to break if something gets stuck in the auger
housing.
Always use genuine spare parts. Other types of
bolts could cause serious damage to the machine.
1. Stop the engine.
2. Disconnect the ignition cable from the spark plug.
3. Ensure all the rotating parts have stopped.
4. Remove the object that has fastened in the auger.
5. Lubricate the auger shaft (see above).
6. Aligne the holes in the shaft and auger.
7. Remove the broken bolt parts.
8. Assemble a new original shear bolt.
7.12 HEADLAMP BULB
Only 27 W original spare part bulb is allowed to be
used. Bulbs with higher power will damage the
headlamp.
The headlamp bulb is fitted to the headlamp by a bayonet
socket. See fig. 17. To replace the bulb proceed as follows:
1. Turn the bulb about 30° CCW and pull it out.
2. Release the plastic locks at each side of the bulb and pull
off the cable connection from the bulb.
3. Fit the new bulb in the reverse order.
8 STORAGE
Never store the snow thrower with petrol in the
tank in a confined area with bad ventilation. Petrol
fumes could reach open flames, sparks, cigarettes
etc.
If the snow thrower is to be stored for a longer period than 30
days, the following measures are recommended:
1. Empty the petrol tank.
2. Start the engine and let it run until it stops due to lack of
fuel.
3. Change the engine oil if it has not been done for 3
months.
4. Remove the spark plug and empty a little engine oil
(about 30ml) in the hole. Crank the engine a couple of
times. Screw back the spark plug.
5. Clean the whole snow thrower thoroughly.
6. Lubricate all the parts as shown in LUBRICATING above.
7. Inspect the snow thrower for damage. Repair if necessary.
8. Touch up any paint damage.
9. Rust protect the metal surfaces.
10. Store the snow thrower indoors if possible.
9 IF SOMETHING BREAKS
Authorised service workshops carry out repairs and
guarantee service. Always use genuine spare parts.
Do you carry out simple repairs yourself? Always use
genuine spare parts. They fit perfectly and make the work
much easier.
Spare parts are available at your retailer and service station.
When ordering spare parts: Specify the model, year of
purchase, the engine model and type number.
10 PURCHASE TERMS
A full warranty is issued against manufacturing and material
defects. The user must carefully follow the instructions given
in the enclosed documentation.
Exceptions:
The warranty does not cover damage due to:
- Neglect by the user to acquaint themselves with
accompanying documentation
- Carelessness
- Incorrect and non-permitted use or assembly
- The use of non-genuine spare parts
- The use of accessories not supplied or approved by GGP
Neither does the guarantee cover:
- Wear parts such as drive belts, augers, headlights, wheels,
shear bolts and wires
- Normal wear
- Engines. These are covered by the engine manufacturer’s
warranties, with separate terms and conditions.
The purchaser is covered the national laws of each by each
country. The rights to which the purchaser is entitled with the
support of these laws are not restricted by this warranty.
Содержание Royal 1171 HST
