background image

 
 

Appendix C Hayes AT Command Reference 

RFI-9256 Radio Modem User Manual 

Page 94 of 109 

 

ATS47=15<CR>

: Sets the frame time to 15ms. 

 

ATS47=20<CR>

: Sets the frame time to 20ms. 

 

ATS47=25<CR>

: Sets the frame time to 25ms. 

 

ATS47=30<CR>

: Sets the frame time to 30ms. 

 

ATS47=35<CR>

: Sets the frame time to 35ms. 

C.2.14 

“ATS48” Frame Bias 

S-register 48 sets the frame bias of the radio. The only valid frame bias values are: 

 

ATS48=0<CR>

: Disables frame bias (sets the bias to 50/50). 

 

ATS48=1<CR>

:  Sets  the  frame  bias  to  outgoing/upload.  This  means  that  more  data  can  flow  out 

from this unit over the air. 

 

ATS48=2<CR>

: Sets the frame bias to incoming/download. This means that more data can flow into 

this unit from the air. 

C.2.15 

“ATS50” Network Address 

S-register  40  sets  the  network  address  of  the  radio.  All  radios  on  a  single  network  must  have  the  same 
network in order to communicate. Valid values are between 0 and 63. 

 

ATS50=54<CR>

: Sets the network address to 54. 

C.2.16 

“ATS51” Unit Rx address 

S-register 51 sets the units local address. Local addresses are in the range 1 to 9999. 

 

ATS51=1001<CR>

: Sets the units address to 1001. 

C.2.17 

“ATS52” Unit Tx address 

S-register 52 sets the destination address for point-to-point traffic from this unit. Destination addresses are in 
the range 0 to 9999. 

 

ATS52=2027<CR>

: Sets the point-to-point destination address to 2027. 

C.2.18 

“ATS60” Set Logging Level 

S-register 60 sets the current radio log level. The only valid values are: 

 

ATS60=0<CR>

: Only errors are logged. 

 

ATS60=1<CR>

: Warnings and errors are logged. 

 

ATS60=2<CR>

: Status information, warnings, and errors are logged. 

Содержание rfi-9256














































































































Отзывы: